- 您現在的位置：買賣IC網 > PDF目錄367809 > PCA9512D (NXP SEMICONDUCTORS) Level shifting hot swappable I2C and SMBus buffer PDF資料下載
參數資料
| 型號： | PCA9512D |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 其它接口 |
| 英文描述： | Level shifting hot swappable I2C and SMBus buffer |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PDSO8 |
| 封裝： | 3.90 MM, PLASTIC, MS-012, SOT-96-1, SOP-8 |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 176K |
| 代理商： | PCA9512D |
Philips Semiconductors
Product data sheet
PCA9512
Level shifting hot swappable I
2
C and SMBus buffer
2004 Oct 05
6
Resistor Pull-up Value Selection
The system pull-up resistors must be strong enough to provide a
positive slew rate of 1.25 V/
μ
s on the SDA and SCL pins, in order to
activate the boost pull-up currents during rising edges. Choose
maximum resistor value using the formula:
R
≤
(V
CC(MIN)
– 0.6) (800,000)/C
where R is the pull-up resistor value in ohms, V
CC(MIN)
is the
minimum V
CC
voltage and C is the equivalent bus capacitance in
picofarads (pF).
In addition, regardless of the bus capacitance, always choose
R
≤
16 k
for V
CC
= 5.5 V maximum, R
≤
24 k
for V
CC
= 3.6 V
maximum. The start-up circuitry requires logic HIGH voltages on
SDAOUT and SCLOUT to connect the backplane to the card, and
these pull-up values are needed to overcome the precharge voltage.
See the curves in Figures 5 and 6 for guidance in resistor pull-up
selection.
30
20
15
21
5
0
0
100
200
300
400
C
BUS
(pF)
R
PULLUP
25
RECOMMENDED
PULL-UP
R
MAX
= 24 k
RISE-TIME > 300 ns
SW02115
Figure 5. Bus requirements for 3.3 V systems
20
15
21
5
0
0
100
200
300
400
C
BUS
(pF)
R
PULLUP
RECOMMENDED
PULL-UP
R
MAX
= 16 k
RISE-TIME
> 300 ns
SW02116
Figure 6. Bus requirements for 5 V systems
Minimum SDA and SCL Capacitance
Requirements
The device connection circuitry requires a minimum capacitance
loading on the SDA and SCL pins in order to function properly. The
value of this capacitance is a function of V
CC
and the bus pull-up
resistance. Estimate the bus capacitance on both the backplane and
the card data and clock buses, and refer to Figures 5 and 6 to
choose appropriate pull-up resistor values. Note from the figures
that 5 V systems should have at least 47 pF capacitance on their
buses and 3.3 V systems should have at least 22 pF capacitance for
proper operation of the PCA9512. Although the device has been
designed to be marginally stable with smaller capacitance loads, for
applications with less capacitance, provisions need to be made to
add a capacitor to ground to ensure these minimum capacitance
conditions if oscillations are noticed during initial signal integrity
verification.
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9512DP | Level shifting hot swappable I2C and SMBus buffer |
| PCA9513A | Hot swappable I2C-bus and SMBus bus buffer |
| PCA9514A | Hot swappable I2C-bus and SMBus bus buffer |
| PCA9516A | 5-channel I2C hub |
| PCA9519 | 4-channel level translating I2C-bus/SMBus repeater |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9512D,112 | 功能描述:緩沖器和線路驅動器 LEVSHIFT I2C/SMBUS BUS BUFFER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PCA9512D,118 | 功能描述:緩沖器和線路驅動器 LEVSHIFT I2C/SMBUS BUS BUFFER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PCA9512DP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Level shifting hot swappable I2C and SMBus buffer |
| PCA9512DP,118 | 功能描述:緩沖器和線路驅動器 LEVSHIFT I2C/SMBUS BUS BUFFER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| PCA9513 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Level translating I2C-bus repeater |
發布緊急采購，3分鐘左右您將得到回復。