參數資料
型號： PCA9510A
廠商： NXP Semiconductors N.V.
英文描述： Hot swappable I2C-bus and SMBus bus buffer
中文描述： 熱插拔I2C總線和SMBus總線緩沖器
文件頁數： 19/23頁
文件大小： 140K
代理商： PCA9510A
PCA9510A_1
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 8 September 2005
19 of 23
Philips Semiconductors
PCA9510A
Hot swappable I
2
C-bus and SMBus bus buffer
14. Soldering
14.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
14.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215
°
C to 270
°
C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
below 225
°
C (SnPb process) or below 245
°
C (Pb-free process)
–
for all BGA, HTSSON..T and SSOP..T packages
–
for packages with a thickness
≥
2.5 mm
–
for packages with a thickness < 2.5 mm and a volume
≥
350 mm
3
so called
thick/large packages.
below 240
°
C (SnPb process) or below 260
°
C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
14.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
相關PDF資料
PDF描述
PCA9511A Hot swappable I2C-bus and SMBus bus buffer
PCA9511DP Hot swappable I2C and SMBus bus buffer
PCA9510 Hot swappable I2C and SMBus bus buffer
PCA9510D Hot swappable I2C and SMBus bus buffer
PCA9510DP Hot swappable I2C and SMBus bus buffer
相關代理商/技術參數
參數描述
PCA9510AD 功能描述:緩沖器和線路驅動器 HOT SWAP I2C/SMBUS BUS BUFFER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
PCA9510AD,112 功能描述:緩沖器和線路驅動器 HOT SWAP I2C/SMBUS RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
PCA9510AD,118 功能描述:緩沖器和線路驅動器 HOT SWAP I2C/SMBUS RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel
PCA9510AD112 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述:
PCA9510ADP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hot swappable I2C-bus and SMBus bus buffer
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*