- 您現在的位置：買賣IC網 > PDF目錄367808 > PCA84C822 (NXP Semiconductors N.V.) 8-bit microcontrollers for remote control transmitters(8位微控制器 （應用于遠程數據傳輸）) PDF資料下載
參數資料
| 型號： | PCA84C822 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit microcontrollers for remote control transmitters(8位微控制器 （應用于遠程數據傳輸）) |
| 中文描述： | 8遠程控制發射機（8位微控制器位微控制器（應用于遠程數據傳輸）） |
| 文件頁數： | 14/24頁 |
| 文件大?。?/td> | 142K |
| 代理商： | PCA84C822 |
1995 May 01
14
Philips Semiconductors
Product specification
8-bit microcontrollers for
remote control transmitters
PCA84C122; 222; 422; 622; 822
15 APPLICATION INFORMATION
Fig.12 PCA84C122A Remote control transmitter application.
P10
P00
P11
P01
P12
P02
P13
P03
P14
P04
P15
P05
P16
P06
P17
P07
84C122A
T1
RESET
VDD
XTAL2
XTAL1
VSS
MCD252
100
27 mA
3.0 V
T0 / INT
OUT
Figure 12 shows the main application of the PCA84C122
as a remote control transmitter. Each key of the transmitter
keypad represents a specific command. The keys are in an
orderly matrix with each key connected between an I/O
line of Port 0 and an I/O line of Port 1.
The lines of Port 0 are designated ‘scan’ (output) lines, and
the lines of Port 1 are ‘sense’ (input) lines.
By making each scan line a logic 0 in turn, and each time
looking at the sense lines, the depressed key is detected.
The corresponding command code is determined by using
a software look-up table. This code together with the
system address is sent according to a coding scheme or
protocol (e.g. RC-5). The pulses that are generated are
available at the OUT pin. This pin drives the output
transistor, which provides the current for the IR-LED.
T0/INT is not used and therefore connected to V
DD
. T1 is
used for system or option selection, therefore a jumper can
be connected to V
DD
or ground.
When more options must be selected, this can be done in
different ways as illustrated in the following two examples:
1.
When the number of keys is sufficiently low a scan line
can be spared. This scan line may be used to connect
a jumper wire to one of the sense lines. Normally the
scan line should be logic 1. When this line is set to
logic 0 the option setting can be read from the sense
lines.
2.
By connecting diodes between one sense line and a
number of scan lines (see Fig.12). If necessary these
diodes can be placed parallel to the keys. When the
sense line is set to logic 0 (acts as scan line), the
option setting can be read from the scan lines (which
act as sense lines and should be set to logic 1
beforehand).
For the oscillator a crystal or ceramic resonator may be
used. A resistor in series with the supply, limits the reverse
current through the IC in the event of the supply voltage
being reversed (i.e. wrong insertion of batteries).
相關PDF資料 |
PDF描述 |
|---|---|
| PCA84C444 | 8-bit microcontrollers with OSD and VST(帶OSD 和 VST的8位微控制器) |
| PCA84C640 | 8-bit microcontrollers with OSD and VST(帶OSD 和 VST的8位微控制器) |
| PCA84C641 | 8-bit microcontrollers with OSD and VST(帶OSD 和 VST的8位微控制器) |
| PCA84C643 | 8-bit microcontrollers with OSD and VST(帶OSD 和 VST的8位微控制器) |
| PCA84C644 | 8-bit microcontrollers with OSD and VST(帶OSD 和 VST的8位微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA84C822A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers for remote control transmitters |
| PCA84C822AP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers for remote control transmitters |
| PCA84C822AT | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers for remote control transmitters |
| PCA84C822ATD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| PCA84C822B | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers for remote control transmitters |
發布緊急采購，3分鐘左右您將得到回復。