參數資料
型號： PCA2002CX8/5/1,025
廠商： NXP Semiconductors
文件頁數： 18/30頁
文件大小： 0K
描述： IC WATCH CIRCUIT 32KHZ DIE
標準包裝： 15,064
系列： *
PCA2002
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 25 November 2011
25 of 30
NXP Semiconductors
PCA2002
32 kHz watch circuit with programmable output period and pulse width
14.3.2 Quality of solder joint
A flip-chip joint is considered to be a good joint when the entire solder land has been
wetted by the solder from the bump. The surface of the joint should be smooth and the
shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps
after reflow can occur during the reflow process in bumps with high ratio of bump diameter
to bump height, i.e. low bumps with large diameter. No failures have been found to be
related to these voids. Solder joint inspection after reflow can be done with X-ray to
monitor defects such as bridging, open circuits and voids.
14.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the
chip from the substrate and replacing it with a new chip. If a chip is removed from the
substrate, most solder balls of the chip will be damaged. In that case it is recommended
not to re-use the chip again.
Device removal can be done when the substrate is heated until it is certain that all solder
joints are molten. The chip can then be carefully removed from the substrate without
damaging the tracks and solder lands on the substrate. Removing the device must be
done using plastic tweezers, because metal tweezers can damage the silicon. The
surface of the substrate should be carefully cleaned and all solder and flux residues
and/or underfill removed. When a new chip is placed on the substrate, use the flux
process instead of solder on the solder lands. Apply flux on the bumps at the chip side as
well as on the solder pads on the substrate. Place and align the new chip while viewing
with a microscope. To reflow the solder, use the solder profile shown in application note
AN10365 “Surface mount reflow soldering description”.
14.3.4 Cleaning
Cleaning can be done after reflow soldering.
相關PDF資料
PDF描述
W3A43C221KAT2A CAP ARRAY 4CH 220PF 25V 0612
W3A41C331KAT2A CAP ARRAY 4CH 330PF 100V 0612
W3A41C221KAT2A CAP ARRAY 4CH 220PF 100V 0612
W2A4ZC103KAT2A CAP ARRAY 4CH 10000PF 10V 0508
3386V-1-502LF TRIMMER 5K OHM 0.5W TH
相關代理商/技術參數
參數描述
PCA2002T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32 kHz watch circuit with programmable output period and pulse width
PCA2002TK 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32 kHz watch circuit with programmable output period and pulse width
PCA2002TK/1,118 功能描述:馬達/運動/點火控制器和驅動器 WATCH IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
PCA2002TK-T 功能描述:馬達/運動/點火控制器和驅動器 WATCH IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
PCA2002U/10AA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:32 kHz watch circuit with programmable output period and pulse width
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*