- 您現在的位置：買賣IC網 > PDF目錄378041 > PBL386202QNS (ERICSSON) Subscriber Line Interface Circuit PDF資料下載
參數資料
| 型號： | PBL386202QNS |
| 廠商： | ERICSSON |
| 英文描述： | Subscriber Line Interface Circuit |
| 中文描述： | 用戶線接口電路 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 135K |
| 代理商： | PBL386202QNS |
PBL 386 20/2
9
SLIC Operating States
State
C3
C2
C1
SLIC operating state
Active detector
0
1
2
3
4
5
6
7
Table 1. SLIC operating states.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Open circuit
Ringing state
Active state
Not applicable
Not applicable
Active state
Not applicable
Not applicable
-
Ring trip detector (active low)
Loop detector (active low)
-
-
Ground key detector (active high)
-
-
14
DR
Input to the ring trip comparator. With DR more positive than DT the detector output, DET, is at logic
level low, indicating off-hook condition. The external ring trip network connects to this input.
15
16
17
18
C3
C2
C1
DET
C1, C2 and C3 are digital inputs (internal pull-up) controlling the SLIC operating states.
Refer to section "Operating states" for details.
Det
ector output. Active low when indicating loop detection and ring trip, active high when indicating ground
key detection.
19
NC
N
o internal
C
onnection.
20
VCC
+5 V power supply.
21
PLD
P
rogrammable
L
oop
D
etector threshold. The loop detection threshold is programmed by a resistor
connected from this pin to AGND.
22
POV
P
rogrammable
O
verhead
V
oltage. If pin is left open: The overhead voltage is internally set to min 1.0 V in
Off-and On-hook. If a resistor is connected between this pin and AGND: the overhead voltage can be set to
higher values.
P
rog.
L
ine
C
urrent, the constant current part of the DC feed characteristic is programmed by a resistor
connected from this pin to AGND.
23
PLC
24
REF
A
Ref
erence, 49.9 k
, resistor should be connected from this pin to AGND.
N
o internal
C
onnection.
25
NC
26
RSN
R
eceive
S
umming
N
ode. 200 times the AC-current flowing into this pin equals the metallic (transversal) AC-
current flowing from RINGX to TIPX. Programming networks for two-wire impedance and
receive gain connect to the receive summing node. A resistor should be connected from this pin to AGND.
27
AGND
Analog Ground, should be tied together with BGND.
28
VTX
Transmit vf output. The AC voltage difference between TIPX and RINGX, the AC metallic voltage, is
reproduced as an unbalanced GND referenced signal at VTX with a gain of one (or one half, see pin PTG).
The two-wire impedance programming network connects between VTX and RSN.
相關PDF資料 |
PDF描述 |
|---|---|
| PBL386212QNT | Subscriber Line Interface Circuit |
| PBL386212SOT | Subscriber Line Interface Circuit |
| PBL38621-2 | Subscriber Line Interface Circuit |
| PBL386212 | Subscriber Line Interface Circuit |
| PBL386212SHT | Subscriber Line Interface Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PBL38620-2QNS | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Subscriber Line Interface Circuit |
| PBL386202QNT | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Subscriber Line Interface Circuit |
| PBL38620-2QNT | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Subscriber Line Interface Circuit |
| PBL386202SHT | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Subscriber Line Interface Circuit |
| PBL38620-2SHT | 制造商:ERICSSON 制造商全稱:Ericsson 功能描述:Subscriber Line Interface Circuit |
發布緊急采購，3分鐘左右您將得到回復。