- 您現在的位置：買賣IC網 > PDF目錄367751 > PA229A Operational Amplifier PDF資料下載
參數資料
| 型號： | PA229A |
| 英文描述： | Operational Amplifier |
| 中文描述： | 運算放大器 |
| 文件頁數： | 5/5頁 |
| 文件大小： | 69K |
| 代理商： | PA229A |
PA28/29
PA28A/29A
Figure 3 shows a bootstrap which dynamically couples the
output waveform onto the V
pin. This causes V
BOOST
to
swing positive from it's initial value, which is equal to +V
(one diode drop), an amount equal to the output. In other
words, if V
was initially 19.3, and the output swings
positive 18 Volts, the voltage on the V
pin will swing to 19.3
-0.7 + 18 or 36.6. The capacitor needs to be sized based on a
1K
impedance and the lowest frequency required by the
circuit. For example, 20Hz will require > 8uF.
I
SENSE
The I
pin is in series with the negative half of the output
stage only. Current will flow through this pin only when nega-
tive current is being outputted. The current that flows in this pin
is the same current that flows in the output (if
–
1A flows in the
output, the I
pin will have 1A of current flow, if +1A flows
in the output the I
pin will have 0 current flow).
The resistor choice is arbitrary and is selected to provide
whatever voltage drop the engineer desires, up to a maximum
of 1.0 volt. However, any voltage dropped across the resistor
will subract from the swing to rail. For instance, assume a +/
–
12 volt power supply and a load that requires +/
–
1A. With no
current sense resistor the output could swing +/
–
10.2 volts. If
a 1
resistor is used for current sense (which will drop 1 Volt
at 1 Amp) then the output could swing +10.2,
–
9.2 Volts.
Figure 4 shows the PA29 I
feature being used to obtain
a Transconductance function. In this example, amplifier "A" is
the master and amplifier "B" is the slave. Feedback from
sensing resistors R
is applied to the summing network and
scaled to the inverting input of amplifier "A" where it is com-
pared to the input voltage. The current sensing feedback
imparts a Transconductance feature to the amplifiers transfer
function. In other words, the voltage developed across the
sensing resistors is directly proportional to the output current.
Using this voltage as a feedback source allows expressing the
gain of the circuit in amperes vs input voltage. The transfer
funcion is approximately:
I
L
+ (V
IN
–
V
REF
) = R
IN
R
FB
*
R
S
In the illustration, resistors R
IN
, R
FB
and R
S
determine gain.
MOUNTING PRECAUTIONS
1. Always use a heat sink. Even unloaded, the PA29 can
dissipate up to 3.6 watts. A thermal washer or thermal
grease should always be used.
2. Avoid bending the leads. Such action can lead to internal
damage.
3. Always fasten the tab to the heat sink before the leads are
soldered to fixed terminals.
4. Strain relief must be provided if there is any probability of
axial stress to the leads.
10
3
7
5
8
PA29A
PA29B
+V
S
≤
20V
D
B1
D
B2
C
B1
SPEAKER
C
B2
FIGURE 3. SIMPLE BOOTSTRAPPING IMPROVES POSITIVE
OUTPUT SWING. CONNECT PINS 3 AND 10 TO V
S
IF NOT
USED. TYPICAL CURRENTS ARE 12
m
A EACH.
A
B
VREF
+VS
VIN
VREF
–
VS OR GND
RS
RS
IL
RL
RIN
RIN
R
PA29
R
RFB
RS
FIGURE 4. I
SENSE
TRANSCONDUCTANCE BRIDGING
AMPLIFIER
This data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible inaccuracies or omissions. All specifications are subject to change without notice.
PA28/29U REV. A MARCH 2000 2000 Apex Microtechnology Corp.
OPERATING
CONSIDERATIONS
相關PDF資料 |
PDF描述 |
|---|---|
| PA29 | Operational Amplifier |
| PA3005 | SILICONE MONOLITHRIC BIPOLAR LINEAR IC |
| PA350 | RISING CLAMP TERMINAL BLOCK |
| PA40 | HIGH VOLTAGE POWER OPERATIONAL AMPLIFIER |
| PA45 | HIGH VOLTAGE POWER OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PA22A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GSM Dielectric PIFA Antenna |
| PA2301 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-DC Converters |
| PA2302 | 制造商:Alltrade Tools LLC 功能描述:5IN FLAT-N-PLIER |
| PA23-020 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| PA23-020I | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。