參數資料
型號： P89LPC936FA,529
廠商： NXP Semiconductors
文件頁數： 42/77頁
文件大小： 0K
描述： IC 80C51 MCU FLASH 16K 28-PLCC
標準包裝： 37
系列： LPC900
核心處理器： 8051
芯體尺寸： 8-位
速度： 18MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，LED，POR，PWM，WDT
輸入/輸出數： 26
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： 閃存
EEPROM 大小： 512 x 8
RAM 容量： 768 x 8
電壓 - 電源 (Vcc/Vdd)： 2.4 V ~ 3.6 V
數據轉換器： A/D 8x8b; D/A 2x8b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-LCC（J 形引線）
包裝： 管件
配用： 622-1014-ND - BOARD FOR LPC9XX TSSOP
622-1008-ND - BOARD FOR LPC9103 10-HVSON
622-1006-ND - SOCKET ADAPTER BOARD
568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X
568-1758-ND - BOARD EVAL FOR LPC93X MCU FAMILY
其它名稱： 568-7915-5
568-7915-5-ND
568-8364-5
935278702529
P89LPC936FA,529-ND
P89LPC936FA-S
P89LPC936FA-S-ND
P89LPC933_934_935_936
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 12 January 2011
47 of 77
NXP Semiconductors
P89LPC933/934/935/936
8-bit microcontroller with accelerated two-clock 80C51 core
8.23.2 Comparator interrupt
Each comparator has an interrupt flag contained in its configuration register. This flag is
set whenever the comparator output changes state. The flag may be polled by software or
may be used to generate an interrupt. The two comparators use one common interrupt
vector. If both comparators enable interrupts, after entering the interrupt service routine,
the user needs to read the flags to determine which comparator caused the interrupt.
8.23.3 Comparators and power reduction modes
Either or both comparators may remain enabled when Power-down or Idle mode is
activated, but both comparators are disabled automatically in Total Power-down mode.
If a comparator interrupt is enabled (except in Total Power-down mode), a change of the
comparator output state will generate an interrupt and wake-up the processor. If the
comparator output to a pin is enabled, the pin should be configured in the push-pull mode
in order to obtain fast switching times while in Power-down mode. The reason is that with
the oscillator stopped, the temporary strong pull-up that normally occurs during switching
on a quasi-bidirectional port pin does not take place.
Comparators consume power in Power-down and Idle modes, as well as in the normal
operating mode. This fact should be taken into account when system power consumption
is an issue. To minimize power consumption, the user can disable the comparators via
PCONA.5, or put the device in Total Power-down mode.
8.24 Keypad interrupt
The Keypad Interrupt (KBI) function is intended primarily to allow a single interrupt to be
generated when Port 0 is equal to or not equal to a certain pattern. This function can be
used for bus address recognition or keypad recognition. The user can configure the port
via SFRs for different tasks.
The Keypad Interrupt Mask register (KBMASK) is used to define which input pins
connected to Port 0 can trigger the interrupt. The Keypad Pattern register (KBPATN) is
used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag
(KBIF) in the Keypad Interrupt Control register (KBCON) is set when the condition is
matched while the Keypad Interrupt function is active. An interrupt will be generated if
enabled. The PATN_SEL bit in the Keypad Interrupt Control register (KBCON) is used to
define equal or not-equal for the comparison.
In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series,
the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key
connected to Port 0 which is enabled by the KBMASK register will cause the hardware to
set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to
wake-up the CPU from Idle or Power-down modes. This feature is particularly useful in
handheld, battery-powered systems that need to carefully manage power consumption
yet also need to be convenient to use.
In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer
than six CCLKs.
相關PDF資料
PDF描述
VE-BTP-IV CONVERTER MOD DC/DC 13.8V 150W
MAX355EWE+T IC MULTIPLEXER DUAL 4X1 16SOIC
VI-BW4-IY-F2 CONVERTER MOD DC/DC 48V 50W
VE-B5J-IV CONVERTER MOD DC/DC 36V 150W
VI-BW4-IY-F1 CONVERTER MOD DC/DC 48V 50W
相關代理商/技術參數
參數描述
P89LPC936FDH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 4 kB/8 kB/16 kB 3 V byte-erasable flash with 8-bit ADCs
P89LPC936FDH,518 功能描述:8位微控制器 -MCU 16K FL/768B RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC936FDH,529 功能描述:8位微控制器 -MCU ORDER P89LPC936FDH-T T/R RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC936FDH/CP324 功能描述:8位微控制器 -MCU P89LPC936FDH/TSSOP28/TUBEDP//C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC936FDH518 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ TS 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ TSSOP-28 制造商:NXP 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*