參數資料
型號: P89LPC907FD
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 71-331814-05S
中文描述: 8-BIT, FLASH, 7.3728 MHz, MICROCONTROLLER, PDSO8
封裝: 3.90 MM, PLASTIC, MS-012, SOT-96-1, SO-8
文件頁數: 34/51頁
文件大?。?/td> 243K
代理商: P89LPC907FD
Philips Semiconductors
P89LPC906/907/908
8-bit microcontrollers with two-clock 80C51 core
Product data
Rev. 05 — 17 December 2004
34 of 51
9397 750 14467
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Reset can be triggered from the following sources:
External reset pin (during power-up or if user configured via UCFG1. This option
must be used for an oscillator frequency above 12 MHz (P89LPC906).)
Power-on detect
Brownout detect
Watchdog Timer
Software reset
UART break character detect reset (P89LPC908).
For every reset source, there is a flag in the Reset Register, RSTSRC. The user can
read this register to determine the most recent reset source. These flag bits can be
cleared in software by writing a ‘0’ to the corresponding bit. More than one flag bit
may be set:
During a power-on reset, both POF and BOF are set but the other flag bits are
cleared.
For any other reset, previously set flag bits that have not been cleared will remain
set.
8.15 Timers/counters 0 and 1
The P89LPC906/907/908 has two general purpose timers which are similar to the
standard 80C51 Timer 0 and Timer 1. These timers have four operating modes
(modes 0, 1, 2, and 3). Modes 0, 1, and 2 are the same for both Timers. Mode 3 is
different. And additional PWM output mode, Mode 6, is provided on the P89LPC907.
8.15.1
Mode 0
Putting either Timer into Mode 0 makes it look like an 8048 Timer, which is an 8-bit
Counter with a divide-by-32 prescaler. In this mode, the Timer register is configured
as a 13-bit register. Mode 0 operation is the same for Timer 0 and Timer 1.
8.15.2
Mode 1
Mode 1 is the same as Mode 0, except that all 16 bits of the timer register are used.
8.15.3
Mode 2
Mode 2 configures the Timer register as an 8-bit Counter with automatic reload.
Mode 2 operation is the same for Timer 0 and Timer 1.
8.15.4
Mode 3
When Timer 1 is in Mode 3 it is stopped. Timer 0 in Mode 3 forms two separate 8-bit
counters and is provided for applications that require an extra 8-bit timer. When
Timer 1 is in Mode 3 it can still be used by the serial port as a baud rate generator for
the P89LPC907 and P89LPC908.
8.15.5
Mode 6 (P89LPC907)
In this mode, the corresponding timer can be changed to a PWM with a full period of
256 timer clocks.
相關PDF資料
PDF描述
P89LPC906 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC906FD 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC907 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC908 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC908FD 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
相關代理商/技術參數
參數描述
P89LPC907FD,112 功能描述:8位微控制器 -MCU PREF PART P89LPC902FD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC908 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC908FD 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC908FD,112 功能描述:8位微控制器 -MCU PREF PART P89LPC903FD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC9102 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock accelerated 80C51 core 1 kB 3 V byte-erasable flash with 8-bit A/D converter