- 您現在的位置：買賣IC網 > PDF目錄367742 > P89LPC906FD (NXP SEMICONDUCTORS) 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM PDF資料下載
參數資料
| 型號： | P89LPC906FD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| 中文描述： | 8-BIT, FLASH, 18 MHz, MICROCONTROLLER, PDSO8 |
| 封裝： | 3.90 MM, PLASTIC, MS-012, SOT-96-1, SO-8 |
| 文件頁數： | 37/51頁 |
| 文件大?。?/td> | 243K |
| 代理商： | P89LPC906FD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
Philips Semiconductors
P89LPC906/907/908
8-bit microcontrollers with two-clock 80C51 core
Product data
Rev. 05 — 17 December 2004
37 of 51
9397 750 14467
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Double buffering can be disabled. If disabled (DBMOD, i.e., SSTAT.7 = ‘0’), the UART
is compatible with the conventional 80C51 UART. If enabled, the UART allows writing
to SnBUF while the previous data is being shifted out. Double buffering is only
allowed in Modes 1, 2 and 3. When operated in Mode 0, double buffering must be
disabled (DBMOD = ‘0’).
8.17.9
Transmit interrupts with double buffering enabled (Modes 1, 2 and 3)
Unlike the conventional UART, in double buffering mode, the Tx interrupt is generated
when the double buffer is ready to receive new data.
8.17.10
The 9
th
bit (bit 8) in double buffering (Modes 1, 2 and 3)
If double buffering is disabled TB8 can be written before or after SBUF is written, as
long as TB8 is updated some time before that bit is shifted out. TB8 must not be
changed until the bit is shifted out, as indicated by the Tx interrupt.
If double buffering is enabled, TB8
must
be updated before SBUF is written, as TB8
will be double-buffered together with SBUF data.
8.18 Analog comparator
An analog comparator is provided on the P89LPC906/907/908. Comparator
operation is such that the output is a logical one (which may be read in a register)
when the positive input is greater than the negative input (selectable from a pin or an
internal reference voltage). Otherwise the output is a zero. The comparator may be
configured to cause an interrupt when the output value changes.
The connections to the comparator are shown in
Figure 16
. The comparator functions
to V
DD
= 2.4 V.
When the comparator is first enabled, the comparator output and interrupt flag are not
guaranteed to be stable for 10 microseconds. The comparator interrupt should not be
enabled during that time, and the comparator interrupt flag must be cleared before
the interrupt is enabled in order to prevent an immediate interrupt service.
When a comparator is disabled the comparator’s output, COx, goes HIGH. If the
comparator output was LOW and then is disabled, the resulting transition of the
comparator output from a LOW to HIGH state will set the comparator flag, CMFx.
This will cause an interrupt if the comparator interrupt is enabled. The user should
therefore disable the comparator interrupt prior to disabling the comparator.
Additionally, the user should clear the comparator flag, CMFx, after disabling the
comparator.
8.19 Internal reference voltage
An internal reference voltage generator may supply a default reference when a single
comparator input pin is used. The value of the internal reference voltage, referred to
as V
REF
, is 1.23 V
±
10 %.
8.20 Comparator interrupt
Each comparator has an interrupt flag contained in its configuration register. This flag
is set whenever the comparator output changes state. The flag may be polled by
software or may be used to generate an interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| P89LPC907 | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC908 | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC908FD | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC912 | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC913 | 8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC906FD,112 | 功能描述:8位微控制器 -MCU PREF PART P89LPC901FD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC907 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
| P89LPC907FD | 功能描述:8位微控制器 -MCU PREF PRT P89LPC902FD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC907FD,112 | 功能描述:8位微控制器 -MCU PREF PART P89LPC902FD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC908 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM |
發布緊急采購，3分鐘左右您將得到回復。