參數資料
型號: P89LPC906FD,112
廠商: NXP Semiconductors
文件頁數: 21/51頁
文件大?。?/td> 0K
描述: IC 80C51 MCU FLASH 1K 8-SOIC
產品培訓模塊: Migrating from 8/16-Bit MCUs to 32-Bit ARMs
標準包裝: 1
系列: LPC900
核心處理器: 8051
芯體尺寸: 8-位
速度: 18MHz
外圍設備: 欠壓檢測/復位,LED,POR,WDT
輸入/輸出數: 6
程序存儲器容量: 1KB(1K x 8)
程序存儲器類型: 閃存
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 2.4 V ~ 3.6 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
包裝: 剪切帶 (CT)
配用: 622-1006-ND - SOCKET ADAPTER BOARD
568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X
其它名稱: 568-1997-1
Philips Semiconductors
P89LPC906/907/908
8-bit microcontrollers with two-clock 80C51 core
Product data
Rev. 05 — 17 December 2004
28 of 51
9397 750 14467
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
The P89LPC906 supports 6 interrupt sources: timers 0 and 1, brownout detect,
watchdog/real-time clock, keyboard, and the comparator.
The P89LPC907 supports 8 interrupt sources: timers 0 and 1, serial port Tx,
combined serial port Rx/Tx (no Rx function is available on this device), brownout
detect, watchdog/real-time clock, keyboard, and the comparator.
The P89LPC908 supports 9 interrupt sources: timers 0 and 1, serial port Tx, serial
port Rx, combined serial port Rx/Tx, brownout detect, watchdog/real-time clock,
keyboard, and the comparator.
Each interrupt source can be individually enabled or disabled by setting or clearing a
bit in the interrupt enable registers IEN0 or IEN1. The IEN0 register also contains a
global disable bit, EA, which disables all interrupts.
Each interrupt source can be individually programmed to one of four priority levels by
setting or clearing bits in the interrupt priority registers IP0, IP0H, IP1, and IP1H. An
interrupt service routine in progress can be interrupted by a higher priority interrupt,
but not by another interrupt of the same or lower priority. The highest priority interrupt
service cannot be interrupted by any other interrupt source. If two requests of
different priority levels are pending at the start of an instruction, the request of higher
priority level is serviced.
If requests of the same priority level are pending at the start of an instruction, an
internal polling sequence determines which request is serviced. This is called the
arbitration ranking. Note that the arbitration ranking is only used to resolve pending
requests of the same priority level.
8.10.1
External interrupt inputs
The P89LPC906/907/908 has a Keypad Interrupt function. This can be used as an
external interrupt input.
If enabled when the P89LPC906/907/908 is put into Power-down or Idle mode, the
interrupt will cause the processor to wake-up and resume operation. Refer to Section
相關PDF資料
PDF描述
P89LPC902FD,112 IC 80C51 MCU FLASH 1K 8-SOIC
P89LPC901FD,112 IC 80C51 MCU FLASH 1K 8-SOIC
DS80C320-ENL IC MCU HI SPEED 33MHZ IND 44TQFP
DS80C323-END IC MCU HI SPEED 18MHZ IND 44TQFP
DS80C320-ENG IC MCU HI SPEED 25MHZ IND 44TQFP
相關代理商/技術參數
參數描述
P89LPC907 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC907FD 功能描述:8位微控制器 -MCU PREF PRT P89LPC902FD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC907FD,112 功能描述:8位微控制器 -MCU PREF PART P89LPC902FD RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC908 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
P89LPC908FD 功能描述:8位微控制器 -MCU 80C51 1K FL 128B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT