- 您現在的位置：買賣IC網 > PDF目錄367742 > P89CE558 (NXP Semiconductors N.V.) Single-chip 8-bit microcontroller(8位單片微控制器) PDF資料下載
參數資料
| 型號： | P89CE558 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Single-chip 8-bit microcontroller(8位單片微控制器) |
| 中文描述： | 單芯片8位微控制器（8位單片微控制器） |
| 文件頁數： | 43/72頁 |
| 文件大小： | 721K |
| 代理商： | P89CE558 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁當前第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Philips Semiconductors
Preliminary specification
P83CE558/P80CE558/P89CE558
Single-chip 8-bit microcontroller
1996 Aug 06
43
6.11.3
The instruction that sets PCON.1 is the last executed prior to going
into the Power-down Mode. Once in Power-down Mode, the HF
oscillator is stopped. The 32 kHz oscillator may stay running. The
content of the on-chip RAM and the Special Function Registers are
preserved. Note that the Power-down Mode can not be entered
when the watchdog has been enabled.
Power-down Mode
The Power-down Mode can be terminated by an external RESET in
the same way as in the 80C51 (RAM is saved, but SFRs are cleared
due to RESET) or in addition by any one of the external interrupts
(INT0, INT1) or Seconds interrupt.
The status of the external pins during Power-down Mode is shown in
Table 40. If the Power-down Mode is activated while in external
program memory, the port data that is held in the Special Function
Register P2 is restored to Port 2.
If the data is a logic1, the port pin is held HIGH during the
Power-down Mode by the strong pull-up transistor P1 (see Figure 9).
The Power-down Mode should not be entered within an interrupt
routine because Wake-up with an external or ‘Seconds’ interrupt is
not possible in that case.
6.11.4
The Power-down Mode of the P8xCE558 can also be terminated by
any one of the three enabled interrupts, INT0, INT1 or Seconds
interrupt.
Wake-up from Power-down Mode
If there is an interrupt already in service, which has same or higher
priority as the Wake-up interrupt, Power-down Mode will switch over
to Idle Mode and stay there until an interrupt of higher priority
terminates Idle Mode.
A termination with these interrupts does not affect the internal data
memory and does not affect the Special Function Registers. This
gives the possibility to exit Power-down without changing the port
output levels. To terminate the Power-down Mode with an external
interrupt, INT0 or INT1 must be switched to be level-sensitive and
must be enabled. The external interrupt input signal INT0 or INT1
must be kept LOW till the oscillator has restarted and stabilized (see
Figure 41). A Seconds interrupt will terminate the Power-down Mode
if it is enabled and INT1 is level sensitive. In order to prevent any
interrupt priority problems during Wake-up, the priority of the desired
Wake-up interrupt should be higher than the priorities of all other
enabled interrupt sources.
The instruction following the one that put the device into the
Power-down Mode will be the first one which will be executed after
the interrupt routine has been serviced.
6.12
The input signal SELXTAL1 connected to logic “1” selects the
XTAL1, 2 oscillator (standard 80C51) instead of the XTAL3, 4
oscillator, which is halted and XTAL3, 4 must not be connected.
Oscillator Circuits
6.12.1
The oscillator circuit of the P8xCE558 is a single-stage inverting
amplifier in a Pierce oscillator configuration. The circuitry between
the XTAL1 and XTAL2 is basically an inverter biased to the transfer
point. Either a crystal or ceramic resonator can be used as the
feedback element to complete the oscillator circuitry. Both are
operated in parallel resonance. XTAL1 is the high gain amplifier
input, and XTAL2 is the output (see Figure 42). To drive the
P8xCE558 externally, XTAL1 is driven from an external source and
XTAL2 left open-circuit (see Figure 43).
XTAL1, 2 Oscillator circuit (standard 80C51)
6.12.2
Please refer to chapter 6.13.1
XTAL3, 4 Circuitry
Figure 42. Using the On-Chip Oscillator.
Quartz crystal
or ceramic
resonator
C1
C2
XTAL1
XTAL2
V
SS
C1 = C2 = 20pF
External
clock
signal
XTAL2
XTAL1
V
SS
Figure 43. Using an external clock.
SELXTAL1
1
SELXTAL1
1
(NC)
相關PDF資料 |
PDF描述 |
|---|---|
| P83CE558 | Single-chip 8-bit microcontroller |
| P89CE558EBB | Single-chip 8-bit microcontroller |
| P89CE558EFB | Single-chip 8-bit microcontroller |
| P80CE558 | Single-chip 8-bit microcontroller(8位單片微控制器) |
| P80CE558EBB | Single-chip 8-bit microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89CE558EBB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P89CE558EFB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller |
| P89CV51RB2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 64 kB flash microcontroller with 1 kB RAM, SPI, 6-clock CPU with 6/12-clock peripherals |
| P89CV51RB2_09 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit 80C51 5 V low power 64 kB flash microcontroller with 1 kB RAM, SPI, 6-clock CPU with 6/12-clock peripherals |
| P89CV51RB2BBC,557 | 制造商:NXP Semiconductors 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。