參數資料
型號： P89C51RC2FB
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
中文描述： 8-BIT, FLASH, 33 MHz, MICROCONTROLLER, PQFP44
封裝： 10 X 10 X 1.75 MM, PLASTIC, SOT-307-2, QFP-44
文件頁數： 41/52頁
文件大?。?/td> 289K
代理商： P89C51RC2FB
Philips Semiconductors
Preliminary specification
89C51RB2/89C51RC2/
89C51RD2
80C51 8-bit Flash microcontroller family
16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
1999 Sep 23
41
+12 V OR + 5 V
+5 V
TxD
RxD
V
SS
V
PP
V
CC
TxD
RxD
RST
XTAL2
XTAL1
SU01299
V
SS
V
CC
89C51RB2
89C51RC2
89C51RD2
Figure 44. In-System Programming with a Minimum of Pins
In-System Programming (ISP)
The In-System Programming (ISP) is performed without removing
the microcontroller from the system. The In-System Programming
(ISP) facility consists of a series of internal hardware resources
coupled with internal firmware to facilitate remote programming of
the 89C51RB2/RC2/RD2 through the serial port. This firmware is
provided by Philips and embedded within each
89C51RB2/RC2/RD2 device.
The Philips In-System Programming (ISP) facility has made in-circuit
programming in an embedded application possible with a minimum
of additional expense in components and circuit board area.
The ISP function uses five pins: TxD, RxD, V
SS
, V
CC
, and V
PP
(see
Figure 44). Only a small connector needs to be available to interface
your application to an external circuit in order to use this feature.
The V
PP
supply should be adequately decoupled and V
PP
not
allowed to exceed datasheet limits.
Using the In-System Programming (ISP)
The ISP feature allows for a wide range of baud rates to be used in
your application, independent of the oscillator frequency. It is also
adaptable to a wide range of oscillator frequencies. This is
accomplished by measuring the bit-time of a single bit in a received
character. This information is then used to program the baud rate in
terms of timer counts based on the oscillator frequency. The ISP
feature requires that an initial character (an uppercase U) be sent to
the 89C51RB2/RC2/RD2 to establish the baud rate. The ISP
firmware provides auto-echo of received characters.
Once baud rate initialization has been performed, the ISP firmware
will only accept Intel Hex-type records. Intel Hex records consist of
ASCII characters used to represent hexadecimal values and are
summarized below:
:NNAAAARRDD..DDCC<crlf>
In the Intel Hex record, the “NN” represents the number of data
bytes in the record. The 89C51RB2/RC2/RD2 will accept up to 16
(10H) data bytes. The “AAAA” string represents the address of the
first byte in the record. If there are zero bytes in the record, this field
is often set to 0000. The “RR” string indicates the record type. A
record type of “00” is a data record. A record type of “01” indicates
the end-of-file mark. In this application, additional record types will
be added to indicate either commands or data for the ISP facility.
The maximum number of data bytes in a record is limited to 16
(decimal). ISP commands are summarized in Table 8.
As a record is received by the 89C51RB2/RC2/RD2, the information
in the record is stored internally and a checksum calculation is
performed. The operation indicated by the record type is not
performed until the entire record has been received. Should an error
occur in the checksum, the 89C51RB2/RC2/RD2 will send an “X”
out the serial port indicating a checksum error. If the checksum
calculation is found to match the checksum in the record, then the
command will be executed. In most cases, successful reception of
the record will be indicated by transmitting a “.” character out the
serial port (displaying the contents of the internal program memory
is an exception).
In the case of a Data Record (record type 00), an additional check is
made. A “.” character will NOT be sent unless the record checksum
matched the calculated checksum and all of the bytes in the record
were successfully programmed. For a data record, an “X” indicates
that the checksum failed to match, and an “R” character indicates
that one of the bytes did not properly program. It is necessary to
send a type 02 record (specify oscillator frequency) to the
89C51RB2/RC2/RD2 before programming data.
The ISP facility was designed to that specific crystal frequencies
were not required in order to generate baud rates or time the
programming pulses. The user thus needs to provide the
89C51RB2/RC2/RD2 with information required to generate the
proper timing. Record type 02 is provided for this purpose.
WinISP, a software utility to implement ISP programming with a PC,
is available from Philips. Commercial serial ISP programmers are
available from third parties. Please check the Philips web site
(www.semiconductors.philips.com) for additional information.
相關PDF資料
PDF描述
P89C51RD2BB 80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RD2BP 80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RD2 80C51 8-bit Flash microcontroller family
P89C51X2 80C51 8-bit Flash microcontroller family
P89C51X2BA 80C51 8-bit Flash microcontroller family
相關代理商/技術參數
參數描述
P89C51RC2FBD/01 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit Flash microcontroller family
P89C51RC2FBD/01,55 功能描述:IC 80C51 MCU FLASH 32K 44-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:89C 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
P89C51RC2FP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RC2HBA 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
P89C51RC2HBB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*