參數資料
型號： P87C591SFA
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： Single-chip 8-bit microcontroller with CAN controller
中文描述： 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC44
封裝： PLASTIC, SOT-187-2, LCC-44
文件頁數： 131/161頁
文件大小： 588K
代理商： P87C591SFA
1999 Aug 19
131
Philips Semiconductors
Objective Specification
Single-chip 8-bit microcontroller with CAN controller
P8xC591
21 INTERRUPTS
The 8xC591 has fifteen interrupt sources, each of which
can be assigned one of four priority levels. The five
interrupt sources common to the 80C51 are the external
interrupts (INT0 and INT1), the timer 0 and timer 1
interrupts (lT0 and IT1), and the serial I/O interrupt (RI or
TI). In the 8xC591, the standard serial interrupt is called
SIO0.
The seven Timer T2 interrupts are generated by flags
CTl0-CTI3, CMl0-CMl1, and by the logical OR of flags
T2OV and T2BO. Flags CTl0 to CTI3 are set by input
signals CT0l to CT3I. The inputs INT2 to INT5 can be
regarded as 4 additional external interrupts, if the capture
facility of Timer T2 is not used (details see Timer T2 in
Section 16.1.4.1).
Flags CMl0 to CMl1 are set when a match occurs between
Timer T2 and the compare registers CM0 and CM1. When
an 8-bit or 16-bit overflow occurs, flags T2BO and T2OV
are set, respectively. These eight flags are not cleared by
hardware and must be reset by software to avoid recurring
interrupts.
The ADC interrupt is generated by the ADCl flag in the
ADC control register (ADCON). This flag is set when an
ADC conversion result is ready to be read. ADCl is not
cleared by hardware and must be reset by software to
avoid recurring interrupts. The SIO1 (I
2
C) interrupt is
generated by the SI flag in the SI01 control register
(S1CON). This flag is set when S1STA is loaded with a
valid status code.
The ADCl flag may be reset by software. It cannot be set
by software. All other flags that generate interrupts may be
set or cleared by software, and the effect is the same as
setting or resetting the flags by hardware. Thus, interrupts
may be generated by software and pending interrupts can
be cancelled by software.
A CAN interrupt is generated (vector address 006BH)
when one or more bits of CANCON register are set (refer
to CAN Section 12.5.5 Interrupt Register (IR) for details).
21.1
Interrupt Enable Registers
Each interrupt source can be individually enabled or
disabled by setting or clearing a bit in the interrupt enable
Special Function Registers lENO and lEN1. All interrupt
sources can also be globally enabled or disabled by setting
or clearing bit EA in lENO. The interrupt enable registers
are described in Section 21.2.1 and 21.2.2).
There are 3 SFRs associated with each of the four-level
interrupts. They are the lENx, lPx, and lPxH (see
Section 21.2.3 to 21.2.6). The lPxH (Interrupt Priority
High) register makes the four-level interrupt structure
possible.
The function of the lPxH SFR is simple and when
combined with the lPx SFR determines the priority of each
interrupt. The priority of each interrupt is determined as
shown in the following table:
Table 92
The priority scheme for servicing the interrupts is the same
as that for the 80C51, except there are four interrupt levels
rather than two as on the 80C51. An interrupt will be
serviced as long as an interrupt of equal or higher priority
is not already being serviced. If an interrupt of equal or
higher level priority is being serviced, the new interrupt will
wait until it is finished before being serviced. If a lower
priority level interrupt is being serviced, it will be stopped
and the new interrupt serviced. When the new interrupt is
finished, the lower priority level interrupt that was stopped
will be completed.
PRIORITY BITS
INTERRUPT PRIORITY LEVEL
IPxH.x
IPx.x
0
0
1
1
0
1
0
1
Level 0 (lowest priority)
Level 1
Level 2
Level 3 (highest priority)
相關PDF資料
PDF描述
P80C591SFB Single-chip 8-bit microcontroller with CAN controller
P83C591SFB Single-chip 8-bit microcontroller with CAN controller
P87C591SFB Single-chip 8-bit microcontroller with CAN controller
P80C591 Single-chip 8-bit microcontroller with CAN controller
P83C591 Single-chip 8-bit microcontroller with CAN controller
相關代理商/技術參數
參數描述
P87C591VFA/00,512 功能描述:8位微控制器 -MCU 80C51 16K OTP/CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87C654X2BBD,157 功能描述:8位微控制器 -MCU 16K/256 OTP 12/6 CLK I2C LQFP RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87C654X2FA 制造商:NXP Semiconductors 功能描述:P87C654X2FA 8bit microcontroller,33MHz
P87C654X2FA,529 功能描述:8位微控制器 -MCU 16K/256 OTP 12/6 CLK RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P87C654X2FA-S 功能描述:8位微控制器 -MCU 16K/256 OTP 12/6 CLK I2C PLCC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*