- 您現在的位置：買賣IC網 > PDF目錄367723 > P83C557E8 (NXP Semiconductors N.V.) 8 BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | P83C557E8 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8 BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 37/72頁 |
| 文件大小： | 374K |
| 代理商： | P83C557E8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
Philips Semiconductors
Product specification
P83C557E4/P80C557E4/P89C557E4
Single-chip 8-bit microcontroller
1999 Mar 02
37
The polling cycle is repeated with every machine cycle, and the
values polled are the values present at S5P2 of the previous
machine cycle. Note that if an interrupt flag is active but is not being
responded to because of one of the above conditions, and if the flag
is inactive when the blocking condition is removed, then the blocked
interrupt will not be serviced. Thus, the fact that the interrupt flag
was once active but not serviced is not remembered. Every polling
cycle is new.
The processor acknowledges an interrupt request by executing a
hardware-generated LCALL to the appropriate service routine. In
some cases it also clears the flag which generated the interrupt, and
in others it does not. It clears the Timer 0, Timer 1, and external
interrupt flags. An external interrupt flag (IE0 or IE1) is cleared only if
it was transition-activated. All other interrupt flags are not cleared by
hardware and must be cleared by the software. The LCALL pushes
the contents of the program counter on to the stack (but it does not
save the PSW) and reloads the PC with an address that depends on
the source of the interrupt being vectored to as shown in Table 38.
Execution proceeds from the vector address until the RETI
instruction is encountered. The RETI instruction clears the “priority
level active” flip-flop that was set when this interrupt was
acknowledged. It then pops the top two bytes from the stack and
reloads the program counter. Execution of the interrupted program
continues from where it was interrupted.
Figure 34. Interrupt enable register (IEN0).
7
6
5
4
3
2
1
0
IEN0 (A8H)
EA
EAD
ES1
ES0
ET1
EX1
ET0
EX0
Table 33.
Description of IEN0 bits
SYMBOL
BIT
FUNCTION
EA
IEN0.7
Global enable/disable control
0 =
No interrupt is enabled
1 =
Any individually enabled interrupt will be accepted
EAD
IEN0.6
Enable ADC interrupt
Enable SIO1 (I
2
C) interrupt
ES1
IEN0.5
ES0
IEN0.4
Enable SIO0 (UART) interrupt
ET1
IEN0.3
Enable Timer 1 interrupt
EX1
IEN0.2
Enable External interrupt 1 / Seconds interrupt
ET0
IEN0.1
Enable Timer 0 interrupt
EX0
IEN0.0
Enable External interrupt 0
相關PDF資料 |
PDF描述 |
|---|---|
| P83C557E4EBB | Single-chip 8-bit microcontroller |
| P83C557E4EFB | Single-chip 8-bit microcontroller |
| P89C557E4EBB | Single-chip 8-bit microcontroller |
| P89C557E4EFB | Single-chip 8-bit microcontroller |
| P83C557E6 | Single-chip 8-bit microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P83C557E8EFB/NNN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|80PIN|PLASTIC |
| P83C562 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller |
| P83C562EBA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller |
| P83C562EBA/031 | 制造商:NXP Semiconductors 功能描述:Electronic Component |
| P83C562EBA/NNN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|LDCC|68PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。