- 您現在的位置：買賣IC網 > PDF目錄369944 > P83C524IBB (NXP SEMICONDUCTORS) 8-bit microcontrollers PDF資料下載
參數資料
| 型號： | P83C524IBB |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-bit microcontrollers |
| 中文描述： | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | 10 X 10 X 1.75 MM, PLASTIC, QFP-44 |
| 文件頁數： | 44/76頁 |
| 文件大小： | 400K |
| 代理商： | P83C524IBB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
1997 Dec 15
44
Philips Semiconductors
Product specification
8-bit microcontrollers
P83C524; P80C528; P83C528
16 OSCILLATOR CIRCUIT
The oscillator circuit of the P83C528 is a single-stage
inverting amplifier in a Pierce oscillator configuration. The
circuitry between the XTAL1 and XTAL2 is basically an
inverter biased to the transfer point. Either a crystal or
ceramic resonator can be used as the feedback element to
complete the oscillator circuitry. Both are operated in
parallel resonance. XTAL1 is the high gain amplifier input,
and XTAL2 is the output (see Fig.22). To drive the
P83C528 externally, XTAL1 is driven from an external
source and XTAL2 left open-circuit (see Fig.23).
Fig.22 P83C528 oscillator circuit.
handbook, halfpage
C1
XTAL1
XTAL2
20 pF
C2
MBC473
20 pF
Fig.23 Driving the P83C528 from an
external source.
handbook, halfpage
XTAL1
XTAL2
MBC472
external clock
(not TTL compatible)
not connected
17 RESET CIRCUIT
The reset circuitry for the P83C528 is connected to the
reset pin RST. A Schmitt trigger is used at the input for
noise rejection. The output of the Schmitt trigger is
sampled by the reset circuitry every machine cycle.
A reset is accomplished by holding the RST pin HIGH for
at least two machine cycles (24 oscillator periods). The
CPU responds by executing an internal reset. During reset
ALE and PSEN output a HIGH level. In order to perform a
correct reset, this level must not be affected by external
elements.
With the P83C528, the RST line can also be pulled HIGH
internally by a pull-up transistor activated by the WDT T3.
The length of the reset pulse from T3 is 16 x 2048 cycles
of the on-chip watchdog oscillator. If the WDT is also used
to reset external devices, the usual capacitor arrangement
should not be connected to RST pin. Instead, an extra
circuit should be used to perform the Power-on Reset
operation. It should be remembered that a Timer T3
overflow, if enabled, will force a reset condition to the
P83C528 by an internal connection, whether the output
RST is tied LOW or not (see Fig.24).
The internal reset is executed during the second cycle in
which RST is pulled HIGH and is repeated every cycle until
RST goes LOW. It leaves the internal registers as shown
by Table 29.
Fig.24 On-chip reset configuration.
handbook, halfpage
MBC476 - 1
SCHMITT
TRIGGER
RESET
CIRCUITRY
overflow
timer T3
VDD
RST
on-chip
resistor
RST
R
相關PDF資料 |
PDF描述 |
|---|---|
| P83C524IFB | 8-bit microcontrollers |
| P83C524IFP | 8-bit microcontrollers |
| P83C524IBP | 8-bit microcontrollers |
| P83C524 | 8-bit microcontrollers |
| P83C524EBA | 8-bit microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P83C524IBP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers |
| P83C524IFA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers |
| P83C524IFB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers |
| P83C524IFP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers |
| P83C528 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。