- 您現在的位置：買賣IC網 > PDF目錄367727 > P83C270AAR (NXP SEMICONDUCTORS) Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC PDF資料下載
參數資料
| 型號： | P83C270AAR |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Microcontrollers for NTSC TVs with On-Screen Display OSD and Closed Caption CC |
| 中文描述： | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PDIP52 |
| 文件頁數： | 45/80頁 |
| 文件大?。?/td> | 266K |
| 代理商： | P83C270AAR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
1999 Jun 11
45
Philips Semiconductors
Product specification
Microcontrollers for NTSC TVs with On-Screen
Display (OSD) and Closed Caption (CC)
P8xCx70 family
18.5
Text display controls
These controls are used for defining the display areas.
Two types of areas are possible. One area is static and
controlled via the main row counter, while the other is
dynamic and can be soft scrolled. The areas cannot cross
each other. Only one soft scroll area is possible.
A scroll map is provided which is addressed by the display
row and contains the address of the data in the memory
that is to be displayed. A bit is also provided to enable the
text display, outside of the scroll area.
Outside the defined scroll area, the scroll map is
addressed by the main row counter. Within the visible soft
scroll area, the scroll map is addressed by the scroll row
counter. The text display enable bit within this area is
ignored.
The number of rows that can be scrolled through can be
set by defining the start row (scroll map value) and end
row. The defined number of rows should be at least one
more than the visible scroll area height.
The height of the visible area is defined as a number of
rows. The position of the scroll area is defined as an offset
in number of rows from the start of the text area.
The values programmed into the registers must ensure a
sensible display. the following should be noted:
If values are programmed that cause the display to go
beyond the vertical sync signal, the display will stop and
react as if finished
If the visible scroll area is made larger than the number
of rows allocated to the scroll function, then they will
wrap around and be repeated
If the defined range of rows for scrolling is greater than
the scroll area, these rows should not be used for other
display purposes.
18.5.1
S
OFT SCROLL ACTION
The soft scrolling function is done by modifying the start
count of the row scan-line count of the first scroll row. This
is decremented once per frame automatically thus
providing the effect of the top row disappearing while the
bottom row is appearing.
At the count 0, the scroll row counter is incremented
automatically and the line-scan counter is set to 12 again.
This pushes the top row to the bottom. This row must be
cleared by the core during the fly-back period.
If the number of rows allocated to the scroll counter is
larger than the defined visible scroll area, this allows parts
of rows at the top and bottom to be displayed during the
scroll function.
Only screens which contain single height rows or only
double height rows can be scrolled.
18.5.1.1
Soft scroll enable
The soft scroll function is started by writing a logic 1 to the
SCRL bit in the Read Only Status Register (see
Section 18.9.9). This bit will be cleared when the scrolling
of one row is completed.
A hard scrolling action can also be performed when writing
a logic 0 to the SCRL bit in the Write Only Status Register.
If a logic 0 is written to this bit, the display in the scroll area
is subsequently shifted up by one row.
Table 61
Soft scroll enable
18.5.1.2
Soft scroll area enable
The SCON bit in the Status Register controls whether a
scroll area is active or not. The default value is no scroll
area enabled, and the display is controlled only by the
scroll map entries. When this bit is set to a logic 1 the scroll
area is activated and the values contained in the SSACR,
SRRR and STA registers take effect.
Table 62
Soft scroll area enable
SCRL
SOFT SCROLL
0
Activates hard scroll, shifts display in one
row increment, stops soft scroll.
Start scrolling function.
1
SCON
SOFT SCROLL AREA
0
1
no scroll area enabled
scroll area enabled
相關PDF資料 |
PDF描述 |
|---|---|
| P83C434CFP | ECONOLINE: RU - Twin Independent Outputs- Output/Output Isolation 1kVDC- Power Sharing on Outputs- Input/Output Isolation 1kVDC- No Heatsink Required- UL94V-0 Package Material- Toroidal Magnetics- No Extern. Components Required- Custom Solutions Available- Efficiency t |
| P83C434 | 8-bit microcontrollers with LCD-driver |
| P83C834 | 8-bit microcontrollers with LCD-driver |
| P83C834CFP | 8-bit microcontrollers with LCD-driver |
| P83C453EFAA | CMOS single-chip 8-bit microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P83C280 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Microcontrollers for monitors with DDC interface, auto-sync detection and sync proc. |
| P83C366 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST |
| P83C366BDA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST |
| P83C366BDR | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST |
| P83C366CBP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Microcontrollers for PAL/SECAM TV with OSD and VST |
發布緊急采購，3分鐘左右您將得到回復。