參數資料
型號: P80C54-1
廠商: INTEL CORP
元件分類: 微控制器/微處理器
英文描述: CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
中文描述: 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PDIP40
封裝: PLASTIC, DIP-40
文件頁數: 5/23頁
文件大?。?/td> 319K
代理商: P80C54-1
8XC52/54/58
If desired, ALE operation can be disabled by setting
bit 0 of SFR location 8EH. With this bit set, the pin is
weakly pulled high. However, the ALE disable fea-
ture will be suspended during a MOVX or MOVC in-
struction, idle mode, power down mode and ICE
mode. The ALE disable feature will be terminated by
reset. When the ALE disable feature is suspended or
terminated, the ALE pin will no longer be pulled up
weakly. Setting the ALE-disable bit has no affect if
the microcontroller is in external execution mode.
Throughout the remainder of this data sheet, ALE
will refer to the signal coming out of the ALE/PROG
pin, and the pin will be referred to as the ALE/PROG
pin.
PSEN:
Program Store Enable is the read strobe to
external Program Memory.
When the 8XC5X is executing code from external
Program Memory, PSEN is activated twice each
machine cycle, except that two PSEN activations
are skipped during each access to external Data
Memory.
EA/V
PP
:
External Access enable. EA must be
strapped to VSS in order to enable the device to
fetch code from external Program Memory locations
0000H to 0FFFFH. Note, however, that if any of the
Lock bits are programmed, EA will be internally
latched on reset.
EA should be strapped to V
CC
for internal program
executions.
This pin also receives the programming supply volt-
age (V
PP
) during EPROM programming.
XTAL1:
Input to the inverting oscillator amplifier.
XTAL2:
Output from the inverting oscillator amplifi-
er.
OSCILLATOR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respec-
tively, of a inverting amplifier which can be config-
ured for use as an on-chip oscillator, as shown in
Figure 3. Either a quartz crystal or ceramic resonator
may be used. More detailed information concerning
the use of the on-chip oscillator is available in Appli-
cation Note AP-155, ‘‘Oscillators for Microcontrol-
lers’’, Order No. 230659.
272336–5
C1, C2
e
30 pF
g
10 pF for Crystals
For Ceramic Resonators, contact resonator manufac-
turer.
Figure 3. Oscillator Connections
To drive the device from an external clock source,
XTAL1 should be driven, while XTAL2 floats, as
shown in Figure 4. There are no requirements on the
duty cycle of the external clock signal, since the in-
put to the internal clocking circuitry is through a di-
vide-by-two flip-flop, but minimum and maximum
high and low times specified on the data sheet must
be observed.
An external oscillator may encounter as much as a
100 pF load at XTAL1 when it starts up. This is due
to interaction between the amplifier and its feedback
capacitance. Once the external signal meets the V
IL
and V
IH
specifications the capacitance will not ex-
ceed 20 pF.
272336–6
Figure 4. External Clock Drive Configuration
IDLE MODE
The user’s software can invoke the Idle Mode. When
the microcontroller is in this mode, power consump-
tion is reduced. The Special Function Registers and
the onboard RAM retain their values during Idle, but
the processor stops executing instructions. Idle
Mode will be exited if the chip is reset or if an en-
abled interrupt occurs.
5
相關PDF資料
PDF描述
P80C54-2 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
P80C54-24 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
P80C54-33 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
P80C58 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
P80C58-1 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
P80C541-1 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:CMOS SINGLE CHIP MICROCONTROLLER
P80C54-2 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
P80C54-20 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
P80C54-24 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
P80C54-33 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER