- 您現在的位置：買賣IC網 > PDF目錄98050 > P045T048T32AL 1-OUTPUT 320 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | P045T048T32AL |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 320 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-16 |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 1064K |
| 代理商： | P045T048T32AL |
vicorpower.com
800-735-6200
VI Chip Pre-Regulator Module
P045F048T32AL
Rev. 2.0
Page 10 of 14
Application Information (continued)
VI Chip Pre-Regulator Module
OVP – Overvoltage Protection
The output Overvoltage Protection set point of the P045F048T32AL is
factory preset for 56 V. If this threshold is exceeded the output shuts
down and a restart sequence is initiated, also indicated by PC pulsing.
If the condition that causes OVP is still present, the unit will again shut
down. This cycle will be repeated until the fault condition is removed.
The OVP set point may be set at the factory to meet unique high
voltage requirements.
PRM Output Power Versus VTM Output Power
As shown in Figure 17, the P045F048T32AL is rated to deliver 6.66 A
maximum, when it is delivering an output voltage in the range from
26 V to 48 V, and 320 W, maximum, when delivering an output
voltage in the range from 48 V to 55 V. When configuring a PRM for
use with a specific VTM, refer to the appropriate VTM data sheet. The
VTM input power can be calculated by dividing the VTM output power
by the VTM efficiency (available from the VTM data sheet). The input
power required by the VTM should not exceed the output power rating
of the PRM.
The Factorized Bus voltage should not exceed an absolute limit of 55 V,
including steady state, ripple and transient conditions. Exceeding this
limit may cause the internal OVP set point to be exceeded.
Parallel Considerations
The PR port is used to connect two PRMs in parallel to form a higher
power array. When configuring arrays, PR port interconnection
terminating impedance is 10 k to SG. See note Page 8 and refer to
Application Note AN002. Additionally one PRM should be designated
as the master while all other PRMs are set as slaves by shorting their
SC pin to SG. The PC pins must be directly connected (no diodes) to
assure a uniform start up sequence. Consult Vicor applications
engineering for applications requiring more than two PRMs.
Adjusting Current Limit
The current limit can be lowered by placing an external resistor
between the IL and SG ports (see Figure 18 for resistor values). With
the IL port open-circuit, the current limit is preset to be within the
range specified in the output specifications table on Page 4.
Input Fuse Recommendations
A fuse should be incorporated at the input to the PRM, in series with
the +In port. A fast acting fuse, NANO2 FUSE 451/453 Series 10 A
125 V, or equivalent, may be required to meet certain safety agency
Conditions of Acceptability. Always ascertain and observe the safety,
regulatory, or other agency specifications that apply to your specific
application.
Product Safety Considerations
If the input of the PRM is connected to SELV or ELV circuits, the output
of the PRM can be considered SELV or ELV respectively.
Application Notes
For PRM and VI Chip application notes on soldering, board layout,
and system design please click on the link below:
Applications Assistance
Please contact Vicor Applications Engineering for assistance,
1-800-927-9474, or email at apps@vicorpower.com.
Current Limit Set Resistors
Current (A)
Resistance
(k
Ω
)
1
10
100
1000
0
1
2
3
45
67
8
Figure 18 — Calculated external resistor value for adjusting current limit,
actual value may vary.
26
30
34
38
42
46
50
54
Factorized Bus Voltage (Vf)
5.8
6.0
6.2
6.4
6.6
6.8
Current
(A)
28
32
36
40
44
48
52
5.6
5.4
5.2
60
20
~
0
22 24
56 58
Safe Operating Area
Figure 17 — P045F048T32AL rating based on Factorized Bus voltage
相關PDF資料 |
PDF描述 |
|---|---|
| P048T048M24AL | 1-OUTPUT 240 W DC-DC REG PWR SUPPLY MODULE |
| P048T048T24AL | 1-OUTPUT 240 W DC-DC REG PWR SUPPLY MODULE |
| P048T048T12AL | 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE |
| P62000NLG8 | DUAL SWITCHING CONTROLLER, QCC64 |
| P62000NLG | DUAL SWITCHING CONTROLLER, QCC64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P0460 | 制造商:Pulse Electronics Corporation 功能描述:Inductor Power Shielded Wirewound 34uH 15% 1A 104mOhm DCR 制造商:Pulse Electronics Corporation 功能描述:Ind Power Shielded Wirewound 34uH 15% 1A |
| P046-06N | 制造商:Tripp Lite 功能描述:12AWG HVY DTY PWR ADPTR 100-250V 制造商:Tripp Lite 功能描述:6IN 12AWG HVY DTY POWER ADPTR CORD 100-250V 20A L5-20P TO 5- - Bulk |
| P0460NLT | 功能描述:固定電感器 ROS 2, 22.95uH 1A 5.3mm Max Ht. RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| P0460T | 功能描述:固定電感器 22.95uH 1A 5.3mm Max Ht. RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| P0461059402 | 制造商:LG Corporation 功能描述:KNOB ARRAY |
發布緊急采購，3分鐘左右您將得到回復。