- 您現在的位置：買賣IC網 > PDF目錄98050 > P045T048T17AL 1-OUTPUT 170 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | P045T048T17AL |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 170 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | ROHS COMPLIANT PACKAGE-16 |
| 文件頁數： | 13/14頁 |
| 文件大?。?/td> | 1245K |
| 代理商： | P045T048T17AL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁
vicorpower.com
800-735-6200
VI Chip Pre-Regulator Module
P045F048T17AL
Rev. 2.1
Page 8 of 14
Pin / Control Functions
VI Chip Pre-Regulator Module
+IN / -In DC Voltage Ports
The VI Chip maximum input voltage should not be exceeded. PRMs
have internal over / undervoltage lockout functions that prevent
operation outside of the specified input range. PRMs will turn on when
the input voltage rises above its undervoltage lockout. If the input
voltage exceeds the overvoltage lockout, PRMs will shut down until the
overvoltage fault clears. PC will toggle indicating an out of bounds
condition.
+Out / -Out Factorized Voltage Output Ports
These ports provide the Factorized Bus voltage output. The –Out port is
connected internally to the –In port through a current sense resistor.
The PRM has a maximum power and a maximum current rating and is
protected if either rating is exceeded. Do not short –Out to –In.
VC – VTM Control
The VTM Control (VC) port supplies an initial VCC voltage to
downstream VTMs, enabling the VTMs and synchronizing the rise of
the VTM output voltage to that of the PRM. The VC port also provides
feedback to the PRM to compensate for voltage drop due to the VTM
output resistance. The PRM’s VC port should be connected to the VTM
VC port. A PRM VC port can drive a maximum of two (2) VTM VC ports.
PC – Primary Control
The PRM voltage output is enabled when the PC pin is open circuit
(floating). To disable the PRM output voltage, the PC pin is pulled low.
Open collector optocouplers, transistors, or relays can be used to
control the PC pin. When using multiple PRMs in a high power array,
the PC ports must be tied together to synchronize their turn on.
During an abnormal condition the PC pin will pulse (Fig.12) as the PRM
initiates a restart cycle. This will continue until the abnormal condition
is rectified. The PC should not be used as an auxiliary voltage supply,
nor should it be switched at a rate greater than 1 Hz.
TM – Factory Use Only
IL – Current Limit Adjust
The PRM has a preset, maximum, current limit set point. The IL port
may be used to reduce the current limit set point to a lower value. See
“adjusting current limits” on page 10.
PR – Parallel Port
The PR port signal, which is proportional to the PRM output power,
supports current sharing of two PRMs. To enable current sharing,
PR ports should be interconnected. Bypass capacitance should be used
when interconnecting PR ports and steps should be taken to minimize
coupling noise into the interconnecting bus. Terminate this port with a
10 k equivalent resistance to SG, e.g. 10 k for a single PRM, 20 k each
for 2 PRMs in parallel, 30 k each for 3 PRMs in parallel etc.. Please
consult Vicor Applications Engineering regarding additional
considerations when paralleling more than two PRMs.
VH – Auxiliary Voltage
VH is a gated (e.g. mirrors PC), non-isolated, nominally 9 Volt,
regulated DC voltage (see “Auxiliary Pins” specifications, on Page 7)
that is referenced to SG. VH may be used to power external circuitry
having a total current consumption of no more than 5 mA under either
transient or steady state conditons including turn-on.
SC – Secondary Control
The load voltage may be controlled by connecting a resistor or voltage
source to the SC port referenced to SG. The slew rate of the output
voltage may be controlled by controlling the rate-of-rise of the voltage
at the SC port (e.g., to limit inrush current into a capacitive load).
SG – Signal Ground
This port provides a low inductance Kelvin connection to –In and
should be used as reference for the OS, CD, SC,VH and IL ports.
OS – Output Set
The application-specific value of the Factorized Bus voltage (Vf) is set
by connecting a resistor between OS and SG. Resistor value selection is
shown in Table 1 on Page 2, and described on Page 9. If no resistor is
connected, the PRM output will be approximately one volt. If set
resistor is not collocated with the PRM, a local bypass capacitor of
~200 pF may be required.
CD – Compensation Device
Adaptive Loop control is configured by connecting an external resistor
between the CD port and SG. Selection of an appropriate resistor value
(see Equation 2 on Page 9 and Table 1 on Page 2) configures the PRM
to compensate for voltage drops in the equivalent output resistance of
the VTM and the PRM-VTM distribution bus. If no resistor is connected
to CD, the PRM will be in Local Loop mode and will regulate the
+Out / –Out voltage to a fixed value.
Figure 15 — PRM pin configuration
Bottom View
4
3
2
1
+OUT
–OUT
+IN
–IN
VC
PC
TM
IL
VH
PR
NC
SG
SC
OS
NC
CD
A
B
C
D
E
F
G
H
J
K
L
M
N
P
AL Version
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Signal Name
Designation
+In
G1-K1,G2-K2
–In
L1-P1, L2-P2
VC
A1,A2
PC
B1, B2
TM
C1, C2
IL
D1, D2
PR
F1, F2
VH
A3, A4
SC
B3, B4
SG
C3, C4
OS
D3, D4
CD
F3, F4
+Out
G3-K3, G4-K4
–Out
L3-P3, L4-P4
相關PDF資料 |
PDF描述 |
|---|---|
| P045T048T32AL | 1-OUTPUT 320 W DC-DC REG PWR SUPPLY MODULE |
| P048T048M24AL | 1-OUTPUT 240 W DC-DC REG PWR SUPPLY MODULE |
| P048T048T24AL | 1-OUTPUT 240 W DC-DC REG PWR SUPPLY MODULE |
| P048T048T12AL | 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE |
| P62000NLG8 | DUAL SWITCHING CONTROLLER, QCC64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P045T048T32AL | 功能描述:V.I CHIP PRM REGULATOR 48V 320W RoHS:是 類別:電源 - 板載 >> DC DC 轉換器（分解式） 系列:V-I Chip™, PRM™ 應用說明:Factorized Power Architecture and V-I Chips 產品培訓模塊:VI Chip Bus Converter Modules 標準包裝:1 系列:V-I Chip™, BCM™ 類型:總線轉換器模塊 輸出數:1 電壓 - 輸入（最小）:330V 電壓 - 輸入（最大）:365V 輸出電壓:12.5V 電流 - 輸出（最大）:24A 電源（瓦） - 制造商系列:300W 電壓 - 隔離:4.242kV（4242V） 應用:商用 特點:具有遠程開/關功能和 UVLO 安裝類型:通孔 封裝/外殼:模塊 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包裝:托盤 工作溫度:-55°C ~ 125°C 效率:95.3% 電源（瓦特）- 最大:300W 重量:0.031 磅（14.06g） |
| P0460 | 制造商:Pulse Electronics Corporation 功能描述:Inductor Power Shielded Wirewound 34uH 15% 1A 104mOhm DCR 制造商:Pulse Electronics Corporation 功能描述:Ind Power Shielded Wirewound 34uH 15% 1A |
| P046-06N | 制造商:Tripp Lite 功能描述:12AWG HVY DTY PWR ADPTR 100-250V 制造商:Tripp Lite 功能描述:6IN 12AWG HVY DTY POWER ADPTR CORD 100-250V 20A L5-20P TO 5- - Bulk |
| P0460NLT | 功能描述:固定電感器 ROS 2, 22.95uH 1A 5.3mm Max Ht. RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| P0460T | 功能描述:固定電感器 22.95uH 1A 5.3mm Max Ht. RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
發布緊急采購，3分鐘左右您將得到回復。