- 您現在的位置：買賣IC網 > PDF目錄363839 > OQ2541U (NXP SEMICONDUCTORS) SDH/SONET data clock recovery unit STM1/4/16 OC3/12/48 GE(SDH/SONET 數據時鐘恢復單元 STM1/4/16 OC3/12/48 GE) PDF資料下載
參數資料
| 型號： | OQ2541U |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | SDH/SONET data clock recovery unit STM1/4/16 OC3/12/48 GE(SDH/SONET 數據時鐘恢復單元 STM1/4/16 OC3/12/48 GE) |
| 中文描述： | CLOCK RECOVERY CIRCUIT, UUC48 |
| 封裝： | DIE-48 |
| 文件頁數： | 6/36頁 |
| 文件大?。?/td> | 172K |
| 代理商： | OQ2541U |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
1999 May 27
6
Philips Semiconductors
Product specification
SDH/SONET data and clock recovery unit
STM1/4/16 OC3/12/48 GE
OQ2541HP; OQ2541U
FUNCTIONAL DESCRIPTION
The OQ2541 recovers data and clock signals from an
incoming high speed bitstream. The input signal on
pins DIN and DINQ is buffered and amplified by the input
circuitry (see Fig.1). The signal is then fed to the Alexander
phase detector where the phase of the incoming data
signal is compared with that of the internal clock. If the
signals are out of phase, the phase detector generates
correction pulses (up or down) that shift the phase of the
Voltage Controlled Ring Oscillator (VCRO) output in
discrete amounts (
) until the clock and data signals are
in phase. The technique used is based on principles first
proposed by J.D.H. Alexander, hence the name of the
phase detector.
Data sampling
The eye pattern of the incoming data is sampled at three
instants A, T and B (see Fig.3). When clock and data
signals are synchronized (locked):
A is the centre of the data bit
T is in the vicinity of the next transition
B is in the centre of the bit following the transition.
If the same level is recorded at both A and B, a transition
has not occurred and no action is taken regardless of the
level T. However, if levels A and B are different a transition
has occurred and the phase detector uses level T to
determine whether the clock was too early or too late with
respect to the data transition.
If levels A and T are the same, but different from level B,
the clock was too early and needs to be slowed down a
little. The Alexander phase detector then generates a
down pulse which stretches a single output pulse from the
ring oscillator by approximately 0.25% which is 1 ps of the
400 ps bit period in the STM16/OC48 mode. This forces
the VCRO to run at a slightly lower frequency for one bit
period. The phase of the clock signal is thus shifted
fractionally with respect to the data signal.
Fig.3 Data sampling.
handbook, halfpage
MGK143
CLOCK
A
T
B
If, on the other hand, levels B and T are the same but
different from level A, the clock was too late and needs to
be speeded up for synchronization. The phase detector
generates an up pulse forcing the VCRO to run at a slightly
higher frequency (+0.25%) for one bit period. The phase of
the clock signal is shifted with respect to the data signal (as
above, but in the opposite direction). Only the proportional
path is active while these phase adjustments are being
made. Because the instantaneous frequency of the VCRO
can be changed only in one of two discrete steps
(
±
0.25%), this type of loop is also known as a Bang/Bang
Phase-Locked Loop (PLL).
If not only the phase but also the frequency of the VCRO
is incorrect, a long train of up or down pulses will be
generated. This pulse train is integrated to generate a
control voltage that is used to shift the centre frequency of
the VCRO. Once the correct frequency has been
established, only the phase will need to be adjusted for
synchronization. The proportional path adjusts the phase
of the clock signal, whereas the integrating path adjusts
the centre frequency.
Frequency window detector
The frequency window detector checks the VCRO
frequency which must be within a 1000 ppm (parts per
million) window around the required frequency.
It compares the output of frequency divider 2 with the
reference frequency on pins CREF and CREFQ
(19.44 or 38.88 MHz; see Table 2). If the VCRO frequency
is found to be outside this window, the frequency window
detector disables the Alexander phase detector and forces
the VCRO output to a frequency within the window.
The phase detector then starts acquiring lock again.
Because of the loose coupling of 1000 ppm, the reference
frequency does not need to be highly accurate or stable.
Any crystal based oscillator that generates a reasonably
accurate frequency (e.g. 100 ppm) will do.
Since sampling point A is always in the centre of the eye
pattern when the data and clock signals are in phase
(locked), the values recorded at this point are taken as the
retrieved data. The data and clock signals are available at
the CML output buffers, which are capable of driving a
50
load.
RF data and clock input circuit
The schematic of the input circuit is shown in Fig.4.
RF data and clock output circuit
The schematic of the output circuit is shown in Fig.5.
相關PDF資料 |
PDF描述 |
|---|---|
| OQ2541HP | SDH/SONET data clock recovery unit STM1/4/16 OC3/12/48 GE(SDH/SONET 數據時鐘恢復單元 STM1/4/16 OC3/12/48 GE) |
| OQ2541 | SDH/SONET data clock recovery unit STM1/4/16 OC3/12/48 GE(SDH/SONET 數據時鐘恢復單元 STM1/4/16 OC3/12/48 GE) |
| OQ2545BHP | SDH/SONET STM16/OC48 laser drivers |
| OQ2545HP | SDH/SONET STM16/OC48 laser drivers |
| OQ8844 | Digital Servo Driver DSD-2 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OQ2545BHP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM16/OC48 laser drivers |
| OQ2545HP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:SDH/SONET STM16/OC48 laser drivers |
| OQ8844 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Servo Driver DSD-2 |
| OQ8868 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital Servo Integrated Circuit Silent DSICS |
| OQ9224HP / C2 | 制造商:PHILIPS-SEMI 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。