- 您現在的位置：買賣IC網 > PDF目錄363838 > OPTA01 Programmable Bar Code Decode ICs PDF資料下載
參數資料
| 型號： | OPTA01 |
| 英文描述： | Programmable Bar Code Decode ICs |
| 中文描述： | 可編程條碼解碼芯片 |
| 文件頁數： | 9/15頁 |
| 文件大小： | 153K |
| 代理商： | OPTA01 |
4-55
Table 3. Summary of Commands - HBCR-2210 Series
Features
Scanner Enable
When enabled, scans with the wand or laser are decoded; otherwise, they are
ignored
Hard Reset
Resets decoder IC as though it were just powered up
Soft Reset
Clears pacing conditions, errors
LED Control Selection
Controls the LED On/Off function
Status Requests
Cause the decoder to generate a status message
General status message showing symbology of last message read, error
conditions, etc.
Message Ready/Not Ready response (for Single Read Mode 2)
Sound Tone
This command causes the reader to sound a tone at the selected pitch for
approximately 100 milliseconds
Configuration Control
There are three operations that manipulate the decoder configuration as a block.
Set default configuration
Save configuration in non-volatile memory
Recall non-volatile configuration
Execute Pending
For use with laser scanning, this command causes immediate execution of
Command
previous commands that would otherwise be postponed until the laser scan
finishes
Description
Table 4. Summary of Other Features - HBCR-2210 Series
Power Idle Mode
Reduces current draw of processor from approximately 20 mA to 4 mA in
wand mode when the wand is inactive
Laser Failure Timeout
Turns off the laser if the Scan Sync signal is missing after approximately
1 second, and sets the laser failure status bit
Self Test Failure Message
An appropriate message is transmitted at power up if the decoder Self Test
fails.
ROM SELF TEST FAILED
EEPROM SELF TEST FAILED
RAM SELF TEST FAILED
An appropriate message is transmitted at power up if the EEPROM
checksum is incorrect.
EEPROM Fault
Recognition
EEPROM FAULT
相關PDF資料 |
PDF描述 |
|---|---|
| Option 010 | Subminiature Right Angle LED Indicators(超小型直角 LED指示器) |
| Option 060 | VDE 0884 Option for Plastic Optocoupler(塑料光耦合器的VDE 0884選擇) |
| Option 102 | T-1 (3 mm) Right Angle LED Indicator Array Options(T-1 (3 mm) 直角LED指示器矩陣) |
| Option 103 | T-1 (3 mm) Right Angle LED Indicator Array Options(T-1 (3 mm) 直角LED指示器矩陣) |
| Option 106 | T-1 (3 mm) Right Angle LED Indicator Array Options(T-1 (3 mm) 直角LED指示器矩陣) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPTA2 | 制造商:Eaton Corporation 功能描述:9000X Series I/O Card (slot B), 2 RO |
| OPTA4 | 制造商:Eaton Corporation 功能描述:9000X Series I/O Card (slot C), Encoder low volt +5v/15v24v |
| OPT-A4-AR-1 | 制造商:ASSEMTECH 功能描述:SENSOR LEVEL 3/8 BSP PNP 制造商:ASSEMTECH 功能描述:SENSOR, LEVEL, 3/8 BSP, PNP, NC 制造商:ASSEMTECH 功能描述:SENSOR, LEVEL, 3/8 BSP, PNP, NC; Output Current:100mA; Sensor Output1:PNP; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes |
| OPT-A4-AR-2 | 制造商:ASSEMTECH 功能描述:SENSOR LEVEL 3/8 BSP PNP 制造商:ASSEMTECH 功能描述:SENSOR, LEVEL, 3/8 BSP, PNP, NO 制造商:ASSEMTECH 功能描述:SENSOR, LEVEL, 3/8 BSP, PNP, NO; Output Current:100mA; Sensor Output1:PNP; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes |
| OPT-A4-AR-3 | 制造商:ASSEMTECH 功能描述:SENSOR LEVEL 3/8 BSP NPN 制造商:ASSEMTECH 功能描述:SENSOR, LEVEL, 3/8 BSP, NPN, NC 制造商:ASSEMTECH 功能描述:SENSOR, LEVEL, 3/8 BSP, NPN, NC; Output Current:100mA; Sensor Output1:NPN; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。