- 您現在的位置：買賣IC網 > PDF目錄363838 > OPT211 MONOLITHIC PHOTODIODE AND AMPLIFIER PDF資料下載
參數資料
| 型號： | OPT211 |
| 英文描述： | MONOLITHIC PHOTODIODE AND AMPLIFIER |
| 中文描述： | 整體式光電二極管與放大器 |
| 文件頁數： | 4/9頁 |
| 文件大小： | 116K |
| 代理商： | OPT211 |
OPT211
4
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with ap-
propriate precautions. Failure to observe proper handling and
installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE DRAWING
NUMBER
(1)
PRODUCT
PACKAGE
OPT211P
8-Pin DIP
006-1
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.
PIN CONFIGURATIONS
MOISTURE SENSITIVITY
AND SOLDERING
Clear plastic does not contain the structural-enhancing fillers
used in black plastic molding compound. As a result, clear
plastic is more sensitive to environmental stress than black
plastic. This can cause difficulties if devices have been stored
in high humidity prior to soldering. The rapid heating during
soldering can stress wire bonds and cause failures. Prior to
soldering, it is recommended that plastic devices be baked-out
at +85
°
C for 24 hours.
The fire-retardant fillers used in black plastic are not compat-
ible with clear molding compound. The OPT211 plastic
packages cannot meet flammability test, UL-94.
Top View
DIP
ABSOLUTE MAXIMUM RATINGS
Supply Voltage ...................................................................................
±
18V
Input Voltage Range ............................................................................
±
V
S
Output Short-Circuit (to ground)............................................... Continuous
Operating Temperature..................................................... –25
°
C to +85
°
C
Storage Temperature ........................................................ –25
°
C to +85
°
C
Junction Temperature ...................................................................... +85
°
C
Lead Temperature (soldering, 10s)................................................ +300
°
C
(Vapor-Phase Soldering Not Recommended)
PACKAGE INFORMATION
V+
–In
V–
NC
Common
PD Anode
NC
V
OUT
1
2
3
4
8
7
6
5
(1)
NOTE: (1) Photodiode location.
相關PDF資料 |
PDF描述 |
|---|---|
| OPT211 | Monolithic Photodiode And Amplifier(單片光電二極管和放大器) |
| OPT301 | INTEGRATED PHOTODIODE AND AMPLIFIER |
| OPT301M | INTEGRATED PHOTODIODE AND AMPLIFIER |
| OPTA01 | Programmable Bar Code Decode ICs |
| Option 010 | Subminiature Right Angle LED Indicators(超小型直角 LED指示器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPT211P-J | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| OPT-25W | 制造商:NIHON 功能描述: |
| OPT3001DNPR | 功能描述:Optical Sensor Ambient 550nm I2C 6-UDFN Exposed Pad 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:環境 波長:550nm 接近探測:無 輸出類型:I2C 電壓 - 電源:1.6 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UDFN 裸露焊盤 供應商器件封裝:6-USON（2x2） 標準包裝:1 |
| OPT3001DNPT | 功能描述:Optical Sensor Ambient 550nm I2C 6-UDFN Exposed Pad 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:環境 波長:550nm 接近探測:無 輸出類型:I2C 電壓 - 電源:1.6 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UDFN 裸露焊盤 供應商器件封裝:6-USON（2x2） 標準包裝:1 |
| OPT3001EVM | 功能描述:OPT3001 - Light, Ambient Sensor Evaluation Board 制造商:texas instruments 系列:- 零件狀態:有效 傳感器類型:環境光 感應范圍:- 接口:I2C 靈敏度:550nm 電壓 - 電源:1.6 V ~ 3.6 V 嵌入式:- 所含物品:2 板，線纜 使用的 IC/零件:OPT3001 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。