參數資料
型號： OPA693IDBVT
英文描述： Ultra-Wideband, Fixed Gain Video BUFFER AMPLIFIER with Disable
中文描述： 超寬帶，固定增益視頻緩沖放大器具有禁用
文件頁數： 14/25頁
文件大?。?/td> 522K
代理商： OPA693IDBVT
OPA693
SBOS285
14
www.ti.com
APPLICATION INFORMATION
WIDEBAND BUFFER OPERATION
The OPA693 gives the exceptional AC performance of a
wideband current-feedback op amp with a highly linear
output stage. It features internal R
F
and R
G
resistors, making
it a simple matter to select a gain of +2, +1 or
–
1 with no
external resistors. Requiring only 13mA supply current, the
OPA693
’
s output swings to within 1V of either supply with
> 700MHz small signal bandwidth and > 300MHz delivering
7V
PP
into a 100
load. This low output headroom in a very
high-speed amplifier gives remarkable single +5V operation.
The OPA693 delivers 2V
PP
swing with > 500MHz bandwidth
operating on a single +5V supply. The primary advantage of
a current-feedback fixed gain video buffer, as opposed to a
slew-enhanced low-gain stable voltage-feedback implemen-
tation, is a higher slew rate with lower quiescent power and
output noise.
Figure 1 shows the DC-coupled, gain of +2V/V, dual power-
supply circuit configuration used as the basis for the
±
5V
Electrical Characteristics table and Typical Characteristics
curves. For test purposes, the input impedance is set to 50
with a resistor to ground and the output impedance is set to
50
with a series output resistor. Voltage swings reported in
the specifications are taken directly at the input and output
pins while load powers (dBm) are defined at a matched 50
load. For the circuit of Figure 1, the total effective load will be
100
|| 600
= 85.7
. The disable control line (
DIS
) is
typically left open to ensure normal amplifier operation. In
addition to the usual power supply decoupling capacitors to
ground, a 0.01
μ
F capacitor can be included between the two
power-supply pins. This optional added capacitor will typi-
cally improve the 2nd harmonic distortion performance by
3dB to 6dB.
Figure 2 shows the DC-coupled, gain of +1V/V buffer con-
figuration used as a starting point for the gain of +1V/V
Typical Characteristic curves. In this case, the inverting input
resistor, R
G
, is left open giving a very broadband gain of +1
performance. While the test circuit shows a 50
input resis-
tor, a buffer application is typically transforming from a
source that cannot drive a heavy load to a 100
load, such
as shown in Figure 2. The noninverting input impedance of
the OPA693 is typically 100k
|| 2pF. Driving directly into
the noninverting input will provide this very light load to the
source. However, the source must still provide the noninverting
input bias current required by the input stage to operate. An
alternative approach to a gain of +1 buffer is described in the
Wideband Unity Gain Buffers section of this data sheet.
OPA693
+5V
5V
50
Load
50
50
50
Source
R
G
300
R
F
300
+
6.8
μ
F
0.1
μ
F
+
6.8
μ
F
0.1
μ
F
V
I
V
O
DIS
Figure 1. DC-Coupled, G = +2, Bipolar-Supply, Specification
and Test Circuit.
Figure 3 shows the DC-coupled, gain of
–
1V/V buffer con-
figuration used as a starting point for the gain of
–
1V/V
Typical Characteristic curves. The input impedance is set to
50
using the parallel combination of an external 60.4
resistor and the internal 300
R
G
resistor. The noninverting
input is tied directly to ground. Since the internal design for
the OPA693 is current-feedback, trying to get improved DC
accuracy by including a resistor on the noninverting input to
ground is ineffective. Using a direct short to ground on the
noninverting input reduces both the contribution of the DC
bias current and noise current to the output error. While the
external 60.4
is used here to match to the 50
source from
the test equipment, the maximum input impedance in this
configuration is limited to the 300
R
G
resistor even with the
R
M
resistor removed. Unlike the noninverting unity gain
buffer application, removing R
M
does not strongly impact the
DC operating point because the short on the noninverting
input of Figure 3 provides the DC operating voltage. This
application of the OPA693 provides a very broadband, high-
output, signal inverter.
Figure 2. DC-Coupled, G = +1V/V, Bipolar-Supply, Specifica-
tion and Test Circuit.
OPA693
+5V
5V
Open
50
Load
50
50
50
Source
R
G
300
R
F
300
+
6.8
μ
F
0.1
μ
F
+
6.8
μ
F
0.1
μ
F
V
I
DIS
V
O
相關PDF資料
PDF描述
OPA694IDBVR Wideband, Low-Power, Current Feedback Operational Amplifier
OPA691 Wideband, Low-Power, Current Feedback Operational Amplifier
OPA694IDR Wideband, Low-Power, Current Feedback Operational Amplifier
OPA683 Wideband, Low-Power, Current Feedback Operational Amplifier
OPA684 Wideband, Low-Power, Current Feedback Operational Amplifier
相關代理商/技術參數
參數描述
OPA693IDBVTG4 功能描述:視頻放大器 Ultra-Widebnd Fixed Gain Video Buffer RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
OPA693IDG4 功能描述:視頻放大器 Ultra-Widebnd Fixed Gain Video Buffer RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
OPA693IDR 功能描述:視頻放大器 Ultra-Widebnd Fixed Gain Video Buffer RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
OPA693IDRG4 功能描述:視頻放大器 Ultra-Widebnd Fixed Gain Video Buffer RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel
OPA694 制造商:BB 制造商全稱:BB 功能描述:Wideband, Low-Power, Current Feedback Operational Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*