- 您現在的位置：買賣IC網 > PDF目錄363781 > OPA680N Wideband, Voltage Feedback OPERATIONAL AMPLIFIER With Disable TM PDF資料下載
參數資料
| 型號： | OPA680N |
| 英文描述： | Wideband, Voltage Feedback OPERATIONAL AMPLIFIER With Disable TM |
| 中文描述： | 寬帶，電壓反饋運算放大器，禁用商標 |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 235K |
| 代理商： | OPA680N |
16
OPA680
amplifier output. For an inverting gain of 2, setting R
G
to
50
for input matching eliminates the need for R
M
but
requires a 100
feedback resistor. This has the interesting
advantage that the noise gain becomes equal to 2 for a 50
source impedance—the same as the non-inverting circuits
considered above. However, the amplifier output will now
see the 100
feedback resistor in parallel with the external
load. In general, the feedback resistor should be limited to
the 200
to 1.5k
range. In this case, it is preferable to
increase both the R
F
and R
G
values as shown in Figure 8,
and then achieve the input matching impedance with a third
resistor (R
M
) to ground. The total input impedance becomes
the parallel combination of R
G
and R
M
.
The second major consideration, touched on in the previ-
ous paragraph, is that the signal source impedance becomes
part of the noise gain equation and hence influences the
bandwidth. For the example in Figure 8, the R
M
value
combines in parallel with the external 50
source imped-
ance, yielding an effective driving impedance of 50
||
67
= 28.6
. This impedance is added in series with R
G
for calculating the noise gain (NG). The resultant NG is 2.8
for Figure 8, as opposed to only 2 if R
M
could be eliminated
as discussed above. The bandwidth will therefore be slightly
lower for the gain of –2 circuit of Figure 8 than for the gain
of +2 circuit of Figure 1.
The third important consideration in inverting amplifier
design is setting the bias current cancellation resistor on the
non-inverting input (R
B
). If this resistor is set equal to the
total DC resistance looking out of the inverting node, the
output DC error, due to the input bias currents, will be
reduced to (Input Offset Current) R
F
. If the 50
source
impedance is DC-coupled in Figure 8, the total resistance to
ground on the inverting input will be 228
. Combining this
in parallel with the feedback resistor gives the R
B
= 146
used in this example. To reduce the additional high fre-
quency noise introduced by this resistor, it is sometimes
bypassed with a capacitor. As long as R
B
<350
, the
capacitor is not required since the total noise contribution of
all other terms will be less than that of the op amp’s input
noise voltage. As a minimum, the OPA680 requires an R
B
value of 50
to damp out parasitic-induced peaking—a
direct short to ground on the non-inverting input runs the
risk of a very high frequency instability in the input stage.
OUTPUT CURRENT AND VOLTAGE
The OPA680 provides output voltage and current capabili-
ties that are unsurpassed in a low cost monolithic op amp.
Under no-load conditions at +25
°
C, the output voltage
typically swings closer than 1V to either supply rail; the
guaranteed swing limit is within 1.2V of either rail. Into a
15
load (the minimum tested load), it is guaranteed to
deliver more than
±
135mA.
The specifications described above, though familiar in the
industry, consider voltage and current limits separately. In
many applications, it is the voltage current, or V-I product,
which is more relevant to circuit operation. Refer to the
“Output Voltage and Current Limitations” plot in the Typi-
cal Performance Curves. The X and Y axes of this graph
show the zero-voltage output current limit and the zero-
current output voltage limit, respectively. The four quad-
rants give a more detailed view of the OPA680’s output
drive capabilities, noting that the graph is bounded by a
“Safe Operating Area” of 1W maximum internal power
dissipation. Superimposing resistor load lines onto the plot
shows that the OPA680 can drive
±
2.5V into 25
or
±
3.5V
into 50
without exceeding the output capabilities or the
1W dissipation limit. A 100
load line (the standard test
circuit load) shows the full
±
3.9V output swing capability,
as shown in the typical specifications.
The minimum specified output voltage and current specifi-
cations over temperature are set by worst-case simulations at
the cold temperature extreme. Only at cold startup will the
output current and voltage decrease to the numbers shown in
the guaranteed tables. As the output transistors deliver power,
their junction temperatures will increase, decreasing their
V
BE
’s (increasing the available output voltage swing) and
increasing their current gains (increasing the available out-
put current). In steady-state operation, the available output
voltage and current will always be greater than that shown
in the over-temperature specifications since the output stage
junction temperatures will be higher than the minimum
specified operating ambient.
To maintain maximum output stage linearity, no output
short-circuit protection is provided. This will not normally
be a problem since most applications include a series match-
ing resistor at the output that will limit the internal power
dissipation if the output side of this resistor is shorted to
ground. However, shorting the output pin directly to the
adjacent positive power supply pin (8-pin packages) will, in
most cases, destroy the amplifier. If additional short-circuit
protection is required, consider a small series resistor in the
power supply leads. This will, under heavy output loads,
reduce the available output voltage swing. A 5
series
resistor will limit the internal power dissipation to 1W for an
output short circuit while decreasing the available output
voltage swing only 0.5V for up to 100mA desired load
currents. Always place the 0.1
μ
F power supply decoupling
capacitors after these supply current limiting resistors di-
rectly on the supply pins.
DRIVING CAPACITIVE LOADS
One of the most demanding and yet very common load
conditions for an op amp is capacitive loading. Often, the
capacitive load is the input of an A/D converter—including
additional external capacitance which may be recommended
to improve A/D linearity. A high speed, high open-loop gain
amplifier like the OPA680 can be very susceptible to de-
creased stability and closed-loop response peaking when a
capacitive load is placed directly on the output pin. When
the amplifier’s open-loop output resistance is considered,
this capacitive load introduces an additional pole in the
signal path that can decrease the phase margin. Several
external solutions to this problem have been suggested.
When the primary considerations are frequency response
flatness, pulse response fidelity and/or distortion, the sim-
plest and most effective solution is to isolate the capacitive
相關PDF資料 |
PDF描述 |
|---|---|
| OPA680P | Wideband, Voltage Feedback OPERATIONAL AMPLIFIER With Disable TM |
| OPA681U | Wideband, Current Feedback OPERATIONAL AMPLIFIER With Disable |
| OPA681 | Wideband, Current Feedback OPERATIONAL AMPLIFIER With Disable |
| OPA681N | Wideband, Current Feedback OPERATIONAL AMPLIFIER With Disable |
| OPA681P | Wideband, Current Feedback OPERATIONAL AMPLIFIER With Disable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA680N/250 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| OPA680N/3K | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| OPA680P | 功能描述:高速運算放大器 Wideband V Feedb RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| OPA680U | 制造商:BB 制造商全稱:BB 功能描述:EVALUATION FIXTURE |
| OPA680U/2K5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
發布緊急采購，3分鐘左右您將得到回復。