- 您現在的位置：買賣IC網 > PDF目錄363779 > OPA632U Low Power, Single-Supply OPERATIONAL AMPLIFIERS TM PDF資料下載
參數資料
| 型號： | OPA632U |
| 英文描述： | Low Power, Single-Supply OPERATIONAL AMPLIFIERS TM |
| 中文描述： | 低功耗，單電源運算放大器商標 |
| 文件頁數： | 17/17頁 |
| 文件大?。?/td> | 176K |
| 代理商： | OPA632U |
17
OPA631, OPA632
nated transmission line is unacceptable, a long trace can be
series-terminated at the source end only. Treat the trace as a
capacitive load in this case and set the series resistor value
as shown in the plot of Recommended R
S
vs Capacitive
Load. This will not preserve signal integrity as well as a
doubly terminated line. If the input impedance of the desti-
nation device is low, there will be some signal attenuation
due to the voltage divider formed by the series output into
the terminating impedance.
e) Socketing a high speed part is not recommended.
The
additional lead length and pin-to-pin capacitance introduced
by the socket can create an extremely troublesome parasitic
network which can make it almost impossible to achieve a
smooth, stable frequency response. Best results are obtained
by soldering the OPA631 and OPA632 onto the board.
INPUT AND ESD PROTECTION
The OPA631 and OPA632 are is built using a very high
speed complementary bipolar process. The internal junction
breakdown voltages are relatively low for these very small
geometry devices. These breakdowns are reflected in the
Absolute Maximum Ratings table. All device pins are pro-
tected with internal ESD protection diodes to the power
supplies as shown in Figure 8.
These diodes provide moderate protection to input overdrive
voltages above the supplies as well. The protection diodes
can typically support 30mA continuous current. Where higher
currents are possible (e.g., in systems with
±
15V supply
parts driving into the OPA631 and OPA632), current-limit-
ing series resistors should be added into the two inputs. Keep
these resistor values as low as possible since high values
degrade both noise performance and frequency response.
External
Pin
+V
CC
–V
CC
Internal
Circuitry
FIGURE 8. Internal ESD Protection.
相關PDF資料 |
PDF描述 |
|---|---|
| OPA633 | High Speed BUFFER AMPLIFIER |
| OPA633KP | High Speed BUFFER AMPLIFIER |
| OPA635 | Wideband, Single Supply OPERATIONAL AMPLIFIERS |
| OPA634N | ECONOLINE: RB & RA - Dual Output from a Single Input Rail- Power Sharing on Output- Industry Standard Pinout- 1kVDC & 2kVDC Isolation- Custom Solutions Available- UL94V-0 Package Material- Efficiency to 85% |
| OPA634U | Wideband, Single Supply OPERATIONAL AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA632U/2K5 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| OPA633 | 制造商:BB 制造商全稱:BB 功能描述:High Speed BUFFER AMPLIFIER |
| OPA6330URO | 制造商:KODENSHI 制造商全稱:KODENSHI KOREA CORP. 功能描述:Ultra Red LED Chip |
| OPA633KP | 功能描述:高速運算放大器 High Speed Buffer Amplifier RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| OPA633KP | 制造商:BURR-BROWN 功能描述:IC AMP BUFFER 275MHZ DIP8 633 制造商:Texas Instruments 功能描述:Buffer Amplifier IC |
發布緊急采購，3分鐘左右您將得到回復。