參數資料
型號: OPA627SM
英文描述: Precision High-Speed Difet OPERATIONAL AMPLIFIERS
中文描述: 精密高速Difet運算放大器
文件頁數: 9/13頁
文件大小: 256K
代理商: OPA627SM
9
OPA627, 637
+
C
2
C
1
R
2
R
1
OPA637
C
1
= C
IN
+ C
STRAY
C
2
= R
1
C
1
R
2
OFFSET VOLTAGE ADJUSTMENT
The OPA627/637 is laser-trimmed for low offset voltage
and drift, so many circuits will not require external adjust-
ment. Figure 3 shows the optional connection of an external
potentiometer to adjust offset voltage. This adjustment should
not be used to compensate for offsets created elsewhere in a
system (such as in later amplification stages or in an A/D
converter) because this could introduce excessive tempera-
ture drift. Generally, the offset drift will change by approxi-
mately 4
μ
V/
°
C for 1mV of change in the offset voltage due
to an offset adjustment (as shown on Figure 3).
FIGURE 2. Circuits with Noise Gain Equal to or Greater than
Five May Use the OPA637.
amp contributes little additional noise. Below 1k
, op amp
noise dominates over the resistor noise, but compares
favorably with precision bipolar op amps.
CIRCUIT LAYOUT
As with any high speed, wide bandwidth circuit, careful
layout will ensure best performance. Make short, direct
interconnections and avoid stray wiring capacitance—espe-
cially at the input pins and feedback circuitry.
The case (TO-99 metal package only) is internally connected
to the negative power supply as it is with most common op
amps. Pin 8 of the plastic DIP, SOIC, and TO-99 packages
has no internal connection.
Power supply connections should be bypassed with good
high frequency capacitors positioned close to the op amp
pins. In most cases 0.1
μ
F ceramic capacitors are adequate.
The OPA627/637 is capable of high output current (in
excess of 45mA). Applications with low impedance loads or
capacitive loads with fast transient signals demand large
currents from the power supplies. Larger bypass capacitors
such as 1
μ
F solid tantalum capacitors may improve dynamic
performance in these applications.
NOISE PERFORMANCE
Some bipolar op amps may provide lower voltage noise
performance, but both voltage noise and bias current noise
contribute to the total noise of a system. The OPA627/637
is unique in providing very low voltage noise and very low
current noise. This provides optimum noise performance
over a wide range of sources, including reactive source
impedances. This can be seen in the performance curve
showing the noise of a source resistor combined with the
noise of an OPA627. Above a 2k
source resistance, the op
FIGURE 4. Connection of Input Guard for Lowest I
B
.
Board Layout for Input Guarding:
Guard top and bottom of board.
Alternate—use Teflon
standoff for sen-
sitive input pins.
Teflon
E.I. du Pont de Nemours & Co.
+
2
3
In
Non-inverting
6
OPA627
Out
+
2
3
In
Inverting
6
OPA627
Out
+
2
3
In
Buffer
6
OPA627
Out
3
2
4
5
6
7
8
No Internal Connection
1
TO-99 Bottom View
To Guard Drive
+
2
3
7
1
5
6
+V
S
–V
S
OPA627/637
100k
10k
to 1M
Potentiometer
(100k
preferred)
±10mV Typical
Trim Range
4
FIGURE 3. Optional Offset Voltage Trim Circuit.
相關PDF資料
PDF描述
OPA640 Wideband Voltage Feedback OPERATIONAL AMPLIFIER
OPA640P Wideband Voltage Feedback OPERATIONAL AMPLIFIER
OPA640U Wideband Voltage Feedback OPERATIONAL AMPLIFIER
OPA640UB Wideband Voltage Feedback OPERATIONAL AMPLIFIER
OPA642 Wideband, Low Distortion, Low Gain OPERATIONAL AMPLIFIER
相關代理商/技術參數
參數描述
OPA628 制造商:BB 制造商全稱:BB 功能描述:Low Distortion Wideband OPERATIONAL AMPLIFIER
OPA628A WAF 制造商:Texas Instruments 功能描述:
OPA628AP 制造商:Texas Instruments 功能描述:Part Number Only
OPA628AU 制造商:Rochester Electronics LLC 功能描述:- Bulk
OPA628U 制造商:BB 制造商全稱:BB 功能描述:EVALUATION FIXTURE