- 您現在的位置：買賣IC網 > PDF目錄363779 > OPA600SM Fast-Settling Wideband OPERATIONAL AMPLIFIER PDF資料下載
參數資料
| 型號： | OPA600SM |
| 元件分類： | 運動控制電子 |
| 英文描述： | Fast-Settling Wideband OPERATIONAL AMPLIFIER |
| 中文描述： | 快速建立寬帶運算放大器 |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 103K |
| 代理商： | OPA600SM |
the OPA600 settling time to
±
1%,
±
0.1%, and
±
0.01%. The
best settling time is achieved in low closed-loop gain cir-
cuits.
Settling time is dependent upon compensation. Under-com-
pensation will result in small phase margin, overshoot or
instability. Over-compensation will result in poor settling
time.
Figure 1 shows the recommended compensation to yield the
specified settling time. Improved or optimum settling time
may be achieved by individually compensating each device
in the user’s circuit since individual devices vary slightly
from one to another, as do user’s circuits.
SLEW RATE
Slew rate is primarily an output, large signal parameter. It
has virtually no dependence upon the closed-loop gain or
small signal bandwidth. Slew rate is dependent upon com-
pensation and decreasing the compensation capacitor value
will increase the available slew rate as shown in the perfor-
mance curve.
The OPA600 slew rate may be increased by using an
alternate compensation as shown in Figure 3. The slew rate
will increase between 700 and 800V/
μ
s typical, with 0.01%
settling time increasing to between 175 and 190ns typical,
and 0.1% settling time increasing to between 110 and 120ns
typical.
For alternate doublet compensation refer to Figure 3. For a
closed-loop gain equal to –1, delete C
and C
and add a
series RC circuit (R = 22
, C = 0.01
μ
F) Between pins 14
and 4. Make no connections to pins 11 and 5. Absolutely
minimize the capacitance to these pins. If a connector is used
for the OPA600, it is recommended that sockets for pins 11
and 5 be removed. For a PC board mount, it is recommended
that the PC board holes be overdrilled for pins 11 and 5 and
adjacent ground plane copper be removed. Effectively, this
compensation places the dominant pole at the input stage,
allowing the output stage to have no compensation and to
slew as fast as possible. Bandwidth and settling time are
impaired only slightly. For closed-loop gains other than –1,
different values of R and C may be required.
FIGURE 4. Offset Null Circuit.
FIGURE 3. Amplifier Circuit for Increased Slew Rate.
OFFSET ADJUSTMENT
The offset voltage of the OPA600 may be adjusted to zero
by connecting a 5k
resistor in series with a 10k
linear
potentiometer in series with another 5k
resistor between
pins 2 and 15, as shown in Figure 4. It is important that one
end of each of the two resistors be located very close to pins
2 and 15 to isolate and avoid loading these sensitive termi-
nals. The potentiometer should be a small noninductive type
with the wiper connected to the positive supply. The leads
connecting these components should be short, no longer
than 0.5-inch, to avoid stray capacitance and stray signal
pick-up. If the potentiometer must be located away from the
immediate vicinity of the OPA600, extreme care must be
observed with the sensitive leads. Locate the two 5k
resistors very close to pins 2 and 15.
Never connect +V
CC
directly to pin 2 or 15. Do not attempt
to eliminate the 5k
resistors because at extreme rotation,
FIGURE 2. Capacitive Load Compensation and Response.
–
+
≈
3pF
(1)
300
600
600
Compensation
Capacitors
Load
Capacitance
e
OUT
125
100
75
50
25
Compensation Capacitance (pF)
L
0
2
4
6
8
10
250
200
150
100
50
0
G
CLOSED LOOP
= –1V/V
Settling
Time
Load
Capacitance
S
NOTE: (1) 3pF typ. should match stray capacitance between pin 3
and common.
e
IN
OPA600
–
6
14
4
600
600
≈
3pF
(1)
3
+
1
13
128
–15VDC
–15VDC
22
0.001μF
16
NOTE: (1) 3pF typ. should match stray capacitance bewteen pin 3 and
common.
–
OPA600
15
2
8
+V
CC
16
3
5k
5k
10k
+
相關PDF資料 |
PDF描述 |
|---|---|
| OPA600TM | Fast-Settling Wideband OPERATIONAL AMPLIFIER |
| OPA620SG | Wideband Precision OPERATIONAL AMPLIFIER |
| OPA620 | Wideband Precision OPERATIONAL AMPLIFIER |
| OPA620KP | Wideband Precision OPERATIONAL AMPLIFIER |
| OPA620KU | Wideband Precision OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA600TM | 制造商:BB 制造商全稱:BB 功能描述:Fast-Settling Wideband OPERATIONAL AMPLIFIER |
| OPA602 | 制造商:BB 制造商全稱:BB 功能描述:High-Speed Precision Difet OPERATIONAL AMPLIFIER |
| OPA602AM | 制造商:Texas Instruments 功能描述: |
| OPA602AP | 功能描述:運算放大器 - 運放 High-Speed Precision Difet RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA602AP | 制造商:BURR-BROWN 功能描述:OP AMP DIFET PRECISION DIP8 602 |
發布緊急采購，3分鐘左右您將得到回復。