- 您現在的位置：買賣IC網 > PDF目錄363769 > OPA335 ELEMENT, FE50M ; PDF資料下載
參數資料
| 型號： | OPA335 |
| 英文描述： | ELEMENT, FE50M ; |
| 中文描述： | 0.05UV/ΣC最大，單電源CMOS運算放大器 |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 354K |
| 代理商： | OPA335 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
7
www.ti.com
OPA334, OPA2334, OPA335, OPA2335
SBOS245D
TYPICAL CHARACTERISTICS
(Cont.)
At T
A
= +25
°
C, V
S
= +5V,
R
L
= 10k
connected to V
S
/2, and V
OUT
= V
S
/2, unless otherwise noted.
APPLICATIONS INFORMATION
The OPA334 and OPA335 series op amps are unity-gain
stable and free from unexpected output phase reversal. They
use auto-zeroing techniques to provide low offset voltage
and very low drift over time and temperature.
Good layout practice mandates use of a 0.1
μ
F capacitor
placed closely across the supply pins.
For lowest offset voltage and precision performance, circuit
layout and mechanical conditions should be optimized. Avoid
temperature gradients that create thermoelectric (Seebeck)
effects in thermocouple junctions formed from connecting
dissimilar conductors. These thermally-generated potentials
can be made to cancel by assuring that they are equal on
both input terminals.
Use low thermoelectric-coefficient connections (avoid dis-
similar metals).
Thermally isolate components from power supplies or
other heat-sources.
Shield op amp and input circuitry from air currents, such as
cooling fans.
Following these guidelines will reduce the likelihood of junc-
tions being at different temperatures, which can cause ther-
moelectric voltages of 0.1
μ
V/
°
C or higher, depending on
materials used.
OPERATING VOLTAGE
The OPA334 and OPA335 series op amps operate over a
power-supply range of +2.7V to +5.5V (
±
1.35V to
±
2.75V).
Supply voltages higher than 7V (absolute maximum) can
permanently damage the amplifier. Parameters that vary
over supply voltage or temperature are shown in the Typical
Characteristics section of this data sheet.
OPA334 ENABLE FUNCTION
The enable/shutdown digital input is referenced to the V
–
supply voltage of the amp. A logic high enables the op amp. A
valid logic high is defined as > 75% of the total supply voltage.
The valid logic high signal can be up to 5.5V above the negative
supply, independent of the positive supply voltage. A valid
logic low is defined as < 0.8V above the V
–
supply pin. If dual
or split power supplies are used, be sure that logic input signals
are properly referred to the negative supply voltage. The
Enable pin must be connected to a valid high or low voltage, or
driven, not left open circuit.
The logic input is a high-impedance CMOS input, with sepa-
rate logic inputs provided on the dual version. For battery-
operated applications, this feature can be used to greatly
reduce the average current and extend battery life.
The enable time is 150
μ
s, which includes one full auto-zero
cycle required by the amplifier to return to V
OS
accuracy.
Prior to this time, the amplifier functions properly, but with
unspecified offset voltage.
Disable time is 1
μ
s. When disabled, the output assumes a
high-impedance state. This allows the OPA334 to be oper-
ated as a gated amplifier, or to have the output multiplexed
onto a common analog output bus.
INPUT VOLTAGE
The input common-mode range extends from (V
–
)
–
0.1V to
(V+)
–
1.5V. For normal operation, the inputs must be limited
to this range. The common-mode rejection ratio is only valid
within the valid input common-mode range. A lower supply
voltage results in lower input common-mode range; there-
fore, attention to these values must be given when selecting
the input bias voltage. For example, when operating on a
single 3V power supply, common-mode range is from 0.1V
below ground to half the power-supply voltage.
COMMON-MODE RANGE vs SUPPLY VOLTAGE
C
2.7
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
–
0.5
3.7
3.2
5.2
5.5
Supply Voltage (V)
4.7
4.2
Minimum Common-Mode
Maximum Common-Mode
SETTLING TIME vs CLOSED-LOOP GAIN
S
μ
s
1
100
10
1
10
Gain (V/V)
100
0.1%
0.01%
Unity-gain
requires one
complete Auto-Zero
Cycle
—
see text.
相關PDF資料 |
PDF描述 |
|---|---|
| OPA335AID | 0.05UV/∑C max, SINGLE-SUPPLY CMOS OPERATIONAL AMPLIFIERS |
| OPA335AIDBVR | 0.05UV/∑C max, SINGLE-SUPPLY CMOS OPERATIONAL AMPLIFIERS |
| OPA335AIDBVT | 0.05UV/∑C max, SINGLE-SUPPLY CMOS OPERATIONAL AMPLIFIERS |
| OPA335AIDR | 0.05UV/∑C max, SINGLE-SUPPLY CMOS OPERATIONAL AMPLIFIERS |
| OPA2338 | MicroSIZE, Single-Supply CMOS OPERATIONAL AMPLIFIERS MicroAmplifier ⑩ Series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA3355 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:200MHz, CMOS OPERATIONAL AMPLIFIER WITH SHUTDOWN |
| OPA3355EA | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述: |
| OPA3355EA/250 | 功能描述:高速運算放大器 2.5V 200MHz GBW CMOS Triple RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| OPA3355EA/250G4 | 功能描述:高速運算放大器 2.5V 200MHz GBW CMOS Triple RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| OPA3355EA/2K5 | 功能描述:高速運算放大器 2.5V 200MHz GBW CMOS Triple RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。