- 您現在的位置：買賣IC網 > PDF目錄376245 > OP470GS (PRECISION MONOLITHICS INC) Very Low Noise Quad Operational Amplifier PDF資料下載
參數資料
| 型號： | OP470GS |
| 廠商： | PRECISION MONOLITHICS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Very Low Noise Quad Operational Amplifier |
| 中文描述： | QUAD OP-AMP, 1500 uV OFFSET-MAX, 6 MHz BAND WIDTH, PDSO16 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 687K |
| 代理商： | OP470GS |
REV. A
OP470
–12–
CAPACITIVE LOAD DRIVING AND POWER
SUPPLY CONSIDERATIONS
The OP470 is unity-gain stable and is capable of driving large
capacitive loads without oscillating. Nonetheless, good supply
bypassing is highly recommended. Proper supply bypassing
reduces problems caused by supply line noise and improves the
capacitive load driving capability of the OP470.
In the standard feedback amplifier, the op amp’s output resistance
combines with the load capacitance to form a low pass filter that
adds phase shift in the feedback network and reduces stability.
A simple circuit to eliminate this effect is shown in Figure 11.
The added components, C1 and R3, decouple the amplifier
from the load capacitance and provide additional stability. The
values of C1 and R3 shown in Figure 11 are for a load capaci-
tance of up to 1000 pF when used with the OP470.
R1
100
*
*
SEE TEXT
R3
50
OP470
C5
0.1 F
*
C4
10 F
+
V–
V
OUT
C
L
1000pF
C1
1000pF
R2
V
IN
PLACE SUPPLY DECOUPLING
CAPACITORS AT OP470
C3
0.1 F
C2
+
V+
Figure 11. Driving Large Capacitive Loads
In applications where the OP470’s inverting or noninverting
inputs are driven by a low source impedance (under 100
W
) or
connected to ground, if V+ is applied before V–, or when V is
disconnected, excessive parasitic currents will flow. Most applica-
tions use dual tracking supplies and with the device supply pins
properly bypassed, power-up will not present a problem. A source
resistance of at least 100
W
in series with all inputs (Figure 11)
will limit the parasitic currents to a safe level if V– is discon-
nected. It should be noted that any source resistance, even 100
W
,
adds noise to the circuit. Where noise is required to be kept at a
minimum, a germanium or Schottky diode can be used to clamp
the V- pin and eliminate the parasitic current flow instead of
using series limiting resistors. For most applications, only one
diode clamp is required per board or system.
UNITY-GAIN BUFFER APPLICATIONS
When Rf
￡
100
W
and the input is driven with a fast, large
signal pulse(> 1 V), the output waveform will look as shown
in Figure 12.
2V/ s
OP470
R1
Figure 12. Pulsed Operation
During the fast feedthrough-like portion of the output, the input
protection diodes effectively short the output to the input, and a
current, limited only by the output short-circuit protection, will
be drawn by the signal generator. With Rf
￡
500
W
, the output
is capable of handling the current requirements (IL < 20 mA at
10 V); the amplifier will stay in its active mode and a smooth
transition will occur.
When Rf > 3 k
W
, a pole created by Rf and the amplifier’s input
capacitance (2 pF) creates additional phase shift and reduces
phase margin. A small capacitor (20 pF to 50 pF) in parallel
with Rf helps eliminate this problem.
APPLICATIONS
Low Noise Amplifier
A simple method of reducing amplifier noise by paralleling
amplifiers is shown in Figure 13. Amplifier noise, depicted in
Figure 14, is around 2 nV/
÷
Hz
@ 1 kHz (R.T.I.). Gain for each
paralleled amplifier and the entire circuit is 1000. The 200
W
resistors limit circulating currents and provide an effective out-
put resistance of 50
W
. The amplifier is stable with a 10 nF
capacitive load and can supply up to 30 mA of output drive.
R2
50k
1/4
OP470E
+15V
–15V
R3
200
R1
50
V
IN
R5
50k
1/4
OP470E
R6
200
R4
50
R8
50k
1/4
OP470E
R9
200
R7
50
R11
50k
1/4
OP470E
R12
200
R10
50
V
OUT
= 1000V
IN
Figure 13. Low Noise Amplifier
相關PDF資料 |
PDF描述 |
|---|---|
| OP482GP | Dual/Quad Low Power, High Speed JFET Operational Amplifiers |
| OP482GS | Dual/Quad Low Power, High Speed JFET Operational Amplifiers |
| OP484 | Precision Rail-to-Rail Input & Output Operational Amplifiers(精密滿幅度輸入輸出運放) |
| OP490FY | Low Voltage Micropower Quad Operational Amplifier |
| OP490AY | Low Voltage Micropower Quad Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP-470GS | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual/Quad Low Noise, Precision Operational Amplifiers |
| OP470GS-REEL | 功能描述:IC OPAMP GP 6MHZ QUAD LN 16SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:150 系列:- 放大器類型:音頻 電路數:2 輸出類型:- 轉換速率:5 V/µs 增益帶寬積:12MHz -3db帶寬:- 電流 - 輸入偏壓:100nA 電壓 - 輸入偏移:500µV 電流 - 電源:6mA 電流 - 輸出 / 通道:50mA 電壓 - 電源，單路/雙路(±):4 V ~ 32 V，±2 V ~ 16 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:8-TSSOP 包裝:管件 |
| OP470GSZ | 功能描述:IC OPAMP GP 6MHZ QUAD LN 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| OP470GSZ-REEL | 功能描述:IC OPAMP GP 6MHZ QUAD LN 16SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| OP471 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Speed, Low Noise Quad Operational Amplifier |
發布緊急采購，3分鐘左右您將得到回復。