- 您現在的位置：買賣IC網 > PDF目錄296741 > OP262DRUZ-REEL (ANALOG DEVICES INC) 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: TSSOP; No of Pins: 8; Temperature Range: Industrial PDF資料下載
參數資料
| 型號： | OP262DRUZ-REEL |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運算放大器 |
| 英文描述： | 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: TSSOP; No of Pins: 8; Temperature Range: Industrial |
| 中文描述： | DUAL OP-AMP, 5000 uV OFFSET-MAX, 15 MHz BAND WIDTH, PDSO8 |
| 封裝： | LEAD FREE, MO-153AA, TSSOP-8 |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 949K |
| 代理商： | OP262DRUZ-REEL |
OP162/OP262/OP462
Rev. F | Page 13 of 20
and VIN swings up to 5 V, the output current will not exceed
30 mA. For single 5 V supply applications, resistors less than
169 are not recommended.
OPx62
VIN
VOUT
169
5V
00288-035
Figure 35. Output Short-Circuit Protection
INPUT OVERVOLTAGE PROTECTION
The input voltage should be limited to ±6 V, or damage to the
device can occur. Electrostatic protection diodes placed in the
input stage of the device help protect the amplifier from static
discharge. Diodes are connected between each input as well as
from each input to both supply pins as shown in the simplified
equivalent circuit in Figure 33. If an input voltage exceeds either
supply voltage by more than 0.6 V, or if the differential input
voltage is greater than 0.6 V, these diodes energize causing
overvoltage damage.
The input current should be limited to less than 5 mA to
prevent degradation or destruction of the device by placing an
external resistor in series with the input at risk of being overdriven.
The size of the resistor can be calculated by dividing the maxi-
mum input voltage by 5 mA. For example, if the differential
input voltage could reach 5 V, the external resistor should be
5 V/5 mA = 1 k. In practice, this resistor should be placed in
series with both inputs to balance any offset voltages created by
the input bias current.
OUTPUT PHASE REVERSAL
The OP162/OP262/OP462 are immune to phase reversal as
long as the input voltage is limited to ±6 V. Figure 30 shows the
output of a device with the input voltage driven beyond the
supply voltages. Although the device’s output does not change
phase, large currents due to input overvoltage could result,
damaging the device. In applications where the possibility of an
input voltage exceeding the supply voltage exists, overvoltage
protection should be used, as described in the previous section.
POWER DISSIPATION
The maximum power that can be safely dissipated by the
OP162/OP262/OP462 is limited by the associated rise in
junction temperature. The maximum safe junction temperature
is 150°C; device performance suffers when this limit is
exceeded. If this maximum is only momentarily exceeded,
proper circuit operation will be restored as soon as the die
temperature is reduced. Leaving the device in an “overheated”
condition for an extended period can result in permanent
damage to the device.
To calculate the internal junction temperature of the OPx62, use
the formula
TJ = PDISS × θJA + TA
where:
TJ is the OPx62 junction temperature.
PDISS is the OPx62 power dissipation.
θJA is the OPx62 package thermal resistance, junction-to-
ambient temperature.
TA is the ambient temperature of the circuit.
The power dissipated by the device can be calculated as
PDISS = ILOAD × (VS – VOUT)
where:
ILOAD is the OPx62 output load current.
VS is the OPx62 supply voltage.
VOUT is the OPx62 output voltage.
Figure 36 and Figure 37 provide a convenient way to determine
if the device is being overheated. The maximum safe power
dissipation can be found graphically, based on the package type
and the ambient temperature around the package. By using the
previous equation, it is a simple matter to see if PDISS exceeds the
device’s power derating curve. To ensure proper operation, it is
important to observe the recommended derating curves shown
AMBIENT TEMPERATURE (
°C)
M
A
XIM
U
M
POW
E
R
D
ISSIPA
TION
(
W
at
ts
)
0.9
0.7
0.8
0.5
0.6
0.1
0.2
0.3
0.4
0
20
40
60
100
80
120
00288-036
8-LEAD SOIC
8-LEAD MSOP
8-LEAD TSSOP
Figure 36. Maximum Power Dissipation vs. Temperature for
8-Lead Package Types
相關PDF資料 |
PDF描述 |
|---|---|
| OP262GS-REEL | 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
| OP262GS-REEL7 | 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
| OP262GSZ | 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
| OP262GSZ-REEL | 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
| OP262GSZ-REEL7 | 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: SOIC; No of Pins: 8; Temperature Range: Industrial |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP262-E-013 | 制造商:Sliger Designs, Inc. 功能描述:MODIFIED OPTICA OP262-E-013 BACK PANELS - Bulk |
| OP262-FNKT | 制造商:Sliger Designs, Inc. 功能描述:FAN CAGE - Bulk |
| OP262GP | 制造商:Rochester Electronics LLC 功能描述:15 MHZ RAIL-TO-RAIL DUAL - Bulk |
| OP262GS | 功能描述:IC OPAMP GP R-R 15MHZ DUAL 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| OP262GS | 制造商:Analog Devices 功能描述:IC SM OP-AMP DUAL 15MHZ RRO/P ((NS)) |
發布緊急采購，3分鐘左右您將得到回復。