- 您現在的位置：買賣IC網 > PDF目錄363670 > NT6868C (Electronic Theatre Controls, Inc.) Keyboard Controller PDF資料下載
參數資料
| 型號： | NT6868C |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Keyboard Controller |
| 中文描述： | 鍵盤控制器 |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 211K |
| 代理商： | NT6868C |
NT6868C
5
Timing Generation
This block generates the system timing and control
signal supplied to the CPU and on-chip peripherals.
There are two types of system clock sources: a built-in
RC oscillator or an external ceramic resonator. Both of
them are mask optional and generate a 4MHz system
clock. They also generate 2MHz for the CPU, and 1 MHz
for the base timer. The following shows the relationship
of code type number with oscillation type.
Oscillator
Code Number
RC OSC
1, 5
External Resistor
3, 7
The following table provides the relationship between
the external resistor and the RC OSC frequency. (This is
for reference only)
External Resistor (K
W
)
RC OSC Frequency (MHz)
39
4.7
43
4.44
47
4
56
3.68
Base Timer
The base timer is an 8-bit counter with a 1MHz clock source. The base timer can be enabled/disabled by the CPU. After a
reset, the base timer is disabled and cleared. The base timer can be preset by writing BT7 - BT0 to the BT register at any
time. When enabled, the base timer starts counting from the preset value. When the value reaches FFH, it generates a
timer interrupt only if the timer interrupt is enabled. When it reaches the maximum value of FFH, the base timer will wrap
around and begin counting at 00H. The timer interval can be programmed from 1 - 256
μ
sec. The base timer can be
enabled by writing a '0' to 'ENBT' in the TCON (Timer Control) register. The ENBT is a level trigger.
Base timer structure:
8-Bit timer
BT7
BT6
BT5
BT4
BT2
BT2
BT1
BT0
BT Pre-loaded Data:
Addr.
Bit
7
6
5
4
3
2
1
0
R/W
$00C0
BT
BT7
BT6
BT5
BT4
BT3
BT2
BT1
BT0
(W)
Timer Control Register:
$00C1
TCON
-
-
-
-
-
-
-
ENBT
(W)
INT. Controller
When a BASE TIMER overflow occurs, it will set the IRQTMR flag. The IRQTMR flag cannot be directly accessed by the
software. Once set by an interrupt source, it remains HIGH unless cleared by writing '1' to the corresponding bit in
CLRIRQX ($00C2H). This register is cleared to '0' on initialization by a system reset.
When an interrupt occurs, the CPU will jump to $FFFEH & $FFFFH to execute the interrupt service routine. When a BASE
TIMER interrupt occurs and enters the interrupt service routine, the IRQTMR flag must be cleared by the software.
Interrupt Control Register:
Addr.
Bit
7
6
5
4
3
2
1
0
R/W
$00C2
CLRIRQX
-
-
-
-
-
-
-
CLRIRQTMR
(W)
1
μ
s
TMRINT
相關PDF資料 |
PDF描述 |
|---|---|
| NT6868CH | Insulation Displacement (IDC) Connector; No. of Contacts:20; Contact Termination:IDC; Gender:Male; Contact Plating:Gold RoHS Compliant: Yes |
| NT6881 | USB Keyboard Micro-Controller |
| NT68F62 | 8-Bit Microcontroller for Monitor (32K Flash MTP Type) |
| NT68F62U | 8-Bit Microcontroller for Monitor (32K Flash MTP Type) |
| NT68P61A | 8-Bit Microcontroller for Monitor (24K OTP ROM Type) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NT6868CH | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Keyboard Controller |
| NT6880 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Keyboard Controller |
| NT6880H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Keyboard Controller |
| NT6881 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB Keyboard Micro-Controller |
| NT68F62 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller for Monitor (32K Flash MTP Type) |
發布緊急采購，3分鐘左右您將得到回復。