- 您現在的位置：買賣IC網 > PDF目錄363668 > NSTM515AS (Electronic Theatre Controls, Inc.) SPECIFICATIONS FOR NICHIA FULL COLOR LED PDF資料下載
參數資料
| 型號： | NSTM515AS |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | SPECIFICATIONS FOR NICHIA FULL COLOR LED |
| 中文描述： | 的日亞的LED全彩規格 |
| 文件頁數： | 6/15頁 |
| 文件大?。?/td> | 558K |
| 代理商： | NSTM515AS |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
-5-
Nichia STSE-CM2199A
<Cat.No.020911>
(4) Soldering Conditions
· Nichia LED lead frames are comprised of a silver plated copper alloy. This substance has a low
thermal coefficient (easily conducts heat). Careful attention should be paid during soldering.
· Solder the LED no closer than 3mm from the base of the epoxy bulb. Soldering beyond the base
of the tie bar is recommended.
· Recommended soldering conditions
Dip Soldering
Pre-Heat
Pre-Heat Time
Solder Bath
Temperature
Dipping Time
Dipping Position
base of the epoxy bulb.
· Do not apply any stress to the lead particularly when heated.
· The LEDs must not be repositioned after soldering.
· After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until
the LEDs return to room temperature.
· Direct soldering onto a PC board should be avoided. Mechanical stress to the resin may be caused
from warping of the PC board or from the clinching and cutting of the lead frames. When it is
absolutely necessary, the LEDs may be mounted in this fashion but the User will assume responsibility
for any problems. Direct soldering should only be done after testing has confirmed that no damage,
such as wire bond failure or resin deterioration, will occur. Nichia’s LEDs should not be soldered
directly to double sided PC boards because the heat will deteriorate the epoxy resin.
· When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize
the mechanical stress on the LEDs.
· Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may
cause failure of the LEDs.
(5) Heat Generation
· Thermal design of the end product is of paramount importance. Please consider the heat generation
of the LED when making the system design. The coefficient of temperature increase per input
electric power is affected by the thermal resistance of the circuit board and density of LED
placement on the board, as well as other components. It is necessary to avoid intense heat generation
and operate within the maximum ratings given in this specification.
· During operation of the LEDs the total power dissipation of the diode elements (red, green, and blue)
within the LEDs must not exceed the maximum power dissipation.
· The operating current should be decided after considering the ambient maximum temperature of LEDs.
(6) Cleaning
· It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using
other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not.
Freon solvents should not be used to clean the LEDs because of worldwide regulations.
· Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic
cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.
Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.
Soldering
300°C Max.
3 seconds Max.
No closer than 3 mm from the
base of the epoxy bulb.
100°C Max.
60 seconds Max.
260°C Max.
10 seconds Max.
No lower than 3 mm from the
Temperature
Soldering Time
Position
相關PDF資料 |
PDF描述 |
|---|---|
| NSVA288 | JRC SAW FILTER |
| NSVA301 | JRC SAW FILTER |
| NSVA321 | 814.5MHz CORDLESS |
| NSVA339 | JRC SAW FILTER |
| NSVA352 | JRC SAW FILTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NSTMXXXXX | 制造商:NICHIA 制造商全稱:NICHIA CORPORATION 功能描述:SPECIFICATIONS FOR NICHIA FULL COLOR LED |
| NSTR1P02T1G | 制造商:ON Semiconductor 功能描述: |
| NSTR4501NT1G | 功能描述:MOSFET NFET 20V 3.2A 80MOH RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| NSTRIO | 制造商:NIGHT SEARCHER 功能描述:HANDLAMP R/CHBL LED BLK UK PL 制造商:NIGHT SEARCHER 功能描述:HANDLAMP, R/CHBL, LED, BLK, UK PL 制造商:NIGHT SEARCHER 功能描述:HANDLAMP, R/CHBL, LED, BLK, UK PL; Depth:128.5mm; External Width:112mm; Length:189mm; Light Source:LED ;RoHS Compliant: Yes |
| NSTRIOY | 制造商:NIGHT SEARCHER 功能描述:HANDLAMP R/CHGB LED YLW UK PL 制造商:NIGHT SEARCHER 功能描述:HANDLAMP, R/CHGB, LED, YLW, UK PL 制造商:NIGHT SEARCHER 功能描述:HANDLAMP, R/CHGB, LED, YLW, UK PL; Length:189mm; Width:112mm; Depth:128.5mm; External Width:112mm; Light Source:LED ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。