- 您現在的位置：買賣IC網 > PDF目錄363666 > NSHU590A (Electronic Theatre Controls, Inc.) SPECIFICATIONS FOR NICHIA UV LED PDF資料下載
參數資料
| 型號： | NSHU590A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | SPECIFICATIONS FOR NICHIA UV LED |
| 中文描述： | 紫外線規格的日亞化學發光二極管 |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 324K |
| 代理商： | NSHU590A |
-5-
Nichia STSE-CH2058C
<Cat.No.
040206
>
(5) Soldering Conditions
· Solder the LED no closer than 3mm from the base of the lead.
· Recommended soldering conditions
Dip Soldering
Pre-Heat
Pre-Heat Time
Solder Bath
Temperature
Dipping Time
Dipping Position
base of the lead.
· Do not apply any stress to the lead particularly when heated.
· The LEDs must not be repositioned after soldering.
· After soldering the LEDs, the lead should be protected from mechanical shock or vibration until
the LEDs return to room temperature.
· Direct soldering onto a PC board should be avoided. Mechanical stress to the glass may be caused
from warping of the PC board or from the clinching and cutting of the leads. When it is
absolutely necessary, the LEDs may be mounted in this fashion but the User will assume responsibility
for any problems. Direct soldering should only be done after testing has confirmed that no damage
,
such as wire bond failure or glass deterioration
,
will occur. Nichia’s LEDs should not be soldered
directly to double sided PC boards because the heat will deteriorate the glass.
· When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize
the mechanical stress on the LEDs.
· Cut the LED leads at room temperature. Cutting the leads at high temperatures may
cause failure of the LEDs.
(6) Heat Generation
· Thermal design of the end product is of paramount importance. Please consider the heat generation
of the LED when making the system design. The coefficient of temperature increase per input
electric power is affected by the thermal resistance of the circuit board and density of LED placement
on the board, as well as other components. It is necessary to avoid intense heat generation and operate
within the maximum ratings given in this specification.
· The operating current should be decided after considering the ambient maximum temperature of LEDs.
(7) Cleaning
· It is recommended that isopropyl alcohol be used
as a solvent for cleaning the LEDs. When using
other solvents, it should be confirmed beforehand
whether the solvents will
dissolve the resin or not.
Freon solvents should not be used to clean the LEDs because of worldwide regulations.
· Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic
cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.
Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs
will occur.
Soldering
350°C Max.
3 seconds Max.
No closer than 3 mm from the
base of the lead.
120°C Max.
60 seconds Max.
260°C Max.
10 seconds Max.
No lower than 3 mm from the
Temperature
Soldering Time
Position
相關PDF資料 |
PDF描述 |
|---|---|
| NSHU590B | SPECIFICATIONS FOR NICHIA UV LED |
| NSPB300A | SPECIFICATIONS FOR NICHIA BLUE LED |
| NSPB310A | SPECIFICATIONS FOR NICHIA BLUE LED |
| NSPB320 | SPECIFICATIONS FOR NICHIA BLUE LED |
| NSPB320BS | SPECIFICATIONS FOR NICHIA BLUE LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NSHU590A | 制造商:MARL International Limited 功能描述:UV EMITTER TO-46 10DEG |
| NSHU590B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SPECIFICATIONS FOR NICHIA UV LED |
| NSHU591A | 制造商:NICHIA 制造商全稱:NICHIA CORPORATION 功能描述:SPECIFICATIONS FOR UV LED |
| NSHU591B | 制造商:NICHIA 制造商全稱:NICHIA CORPORATION 功能描述:SPECIFICATIONS FOR UV LED |
| NSHWREVIEW | 制造商:Digi International Inc 功能描述:DESIGN SUPPORT NET+WORKS |
發布緊急采購，3分鐘左右您將得到回復。