- 您現在的位置：買賣IC網 > PDF目錄363356 > NM27P512VE150 (NATIONAL SEMICONDUCTOR CORP) 524,288-Bit (64K x 8) Processor Oriented CMOS EPROM PDF資料下載
參數資料
| 型號： | NM27P512VE150 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | PROM |
| 英文描述： | 524,288-Bit (64K x 8) Processor Oriented CMOS EPROM |
| 中文描述： | 64K X 8 OTPROM, 150 ns, PQCC32 |
| 封裝： | PLASTIC, LCC-32 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 176K |
| 代理商： | NM27P512VE150 |
Functional Description
DEVICE OPERATION
The six modes of operation of the EPROM are listed in Ta-
ble I. It should be noted that all inputs for the six modes are
at TTL levels. The power supplies required are V
CC
and
OE/V
PP
. The OE/V
PP
power supply must be at 12.75V dur-
ing the three programming modes, and must be at 5V in the
other three modes. The V
CC
power supply must be at 6.25V
during the three programming modes, and at 5V in the other
three modes.
Read Mode
The EPROM has two control functions, both of which must
be logically active in order to obtain data at the outputs.
Chip Enable (CE/PGM) is the power control and should be
used for device selection. Output Enable (OE/V
PP
) is the
output control and should be used to gate data to the output
pins, independent of device selection. Assuming that ad-
dresses are stable, address access time (t
ACC
) is equal to
the delay from CE to output (t
CE
). Data is available at the
outputs t
OE
after the falling edge of OE, assuming that CE
has been low and addresses have been stable for at least
t
ACC
–t
OE
.
Standby Mode
The EPROM has a standby mode which reduces the active
power dissipation by over 99%, from 385 mW to 0.55 mW.
The EPROM is placed in the standby mode by applying a
CMOS high signal to the CE/PGM input. When in standby
mode, the outputs are in a high impedance state, indepen-
dent of the OE input.
Output Disable
The EPROM is placed in output disable by applying a TTL
high signal to the OE input. When in output disable all cir-
cuitry is enabled, except the outputs are in a high imped-
ance state (TRI-STATE).
Output OR-Typing
Because the EPROM is usually used in larger memory ar-
rays, National has provided a 2-line control function that
accommodates this use of multiple memory connections.
The 2-line control function allows for:
a) the lowest possible memory power dissipation, and
b) complete assurance that output bus contention will not
occur.
To most efficiently use these two control lines, it is recom-
mended that CE/PGM be decoded and used as the primary
device selecting function, while OE/V
PP
be made a com-
mon connection to all devices in the array and connected to
the READ line from the system control bus.
This assures that all deselected memory devices are in their
low power standby modes and that the output pins are ac-
tive only when data is desired from a particular memory de-
vice.
Programming
CAUTION: Exceeding 14V on pin 22 (OE/V
PP
) will damage
the EPROM.
Initially, and after each erasure, all bits of the EPROM are in
the ‘‘1’s’’ state. Data is introduced by selectively program-
ming ‘‘0’s’’ into the desired bit locations. Although only
‘‘0’s’’ will be programmed, both ‘‘1’s’’ and ‘‘0’s’’ can be pre-
sented in the data word. The only way to change a ‘‘0’’ to a
‘‘1’’ is by ultraviolet light erasure.
The EPROM is in the programming mode when the OE/V
PP
is at 12.75V. It is required that at least a 0.1
m
F capacitor be
placed across V
CC
to ground to suppress spurious voltage
transients which may damage the device. The data to be
programmed is applied 8 bits in parallel to the data output
pins. The levels required for the address and data inputs are
TTL.
When the address and data are stable, an active low, TTL
program pulse is applied to the CE/PGM input. A program
pulse must be applied at each address location to be pro-
grammed.
The EPROM is programmed with the Fast Programming Al-
gorithm shown in Figure 1. Each Address is programmed
with a series of 100
m
s pulses until it verifies good, up to a
maximum of 25 pulses. Most memory cells will program with
a single 100
m
s pulse.
The EPROM must not be programmed with a DC signal ap-
plied to the CE/PGM input.
Programming multiple EPROM in parallel with the same
data can be easily accomplished due to the simplicity of
the programming requirements. Like inputs of the parallel
EPROM may be connected together when they are pro-
grammed with the same data. A low level TTL pulse applied
to the CE/PGM input programs the paralleled EPROM.
Program Inhibit
Programming multiple EPROMs in parallel with different
data is also easily accomplished. Except for CE/PGM all
like inputs (including OE/V
PP
) of the parallel EPROMs may
be common. A TTL low level program pulse applied to an
EPROM’s CE/PGM input with OE/V
PP
at 12.75V will pro-
gram that EPROM. A TTL high level CE/PGM input inhibits
the other EPROMs from being programmed.
7
相關PDF資料 |
PDF描述 |
|---|---|
| NM27P512VE200 | 524,288-Bit (64K x 8) Processor Oriented CMOS EPROM |
| NM27P512Q120 | 7 #22 PVC PVC RoHS Compliant: Yes |
| NM27P512Q150 | Multiconductor Cable; Number of Conductors:30; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Material:Polyvinylchloride (PVC); Conductor Material:Copper; Conductor Plating:Tin; Jacket Color:Chrome RoHS Compliant: Yes |
| NM27P512Q200 | Multiconductor Cable; Number of Conductors:30; Conductor Size AWG:22; No. Strands x Strand Size:7 x 30; Jacket Material:Polyvinylchloride (PVC); Leaded Process Compatible:Yes; Conductor Material:Copper; Voltage Nom.:300V RoHS Compliant: Yes |
| NM27P512NE120 | Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NM27P512VE200 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:524,288-Bit (64K x 8) Processor Oriented CMOS EPROM |
| NM-28-R28 | 功能描述:LOOP CLAMP W/EYELET GRN 1-3/4" RoHS:是 類別:線纜，導線 - 管理 >> 線夾和夾具 系列:NM-R 標準包裝:100 系列:TC 類型:C-夾 開口尺寸:0.79" L x 0.54" W x 0.67" H（20.1mm x 13.7mm x 17.0mm） 安裝類型:釘子 材質:聚丙烯 顏色:黑 |
| NM29A040 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:4-Mbit/8-Mbit CMOS Serial FLASH E2PROM |
| NM29A040EM | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:4-Mbit/8-Mbit CMOS Serial FLASH E2PROM |
| NM29A040EV | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:4-Mbit/8-Mbit CMOS Serial FLASH E2PROM |
發布緊急采購，3分鐘左右您將得到回復。