- 您現在的位置：買賣IC網 > PDF目錄363237 > NCV8842 (ON SEMICONDUCTOR) 1.5 A, 170 kHz, Buck Regulator with Synchronization Capability PDF資料下載
參數資料
| 型號： | NCV8842 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | 1.5 A, 170 kHz, Buck Regulator with Synchronization Capability |
| 中文描述： | 1.5甲，170千赫，降壓穩壓器的同步功能 |
| 文件頁數： | 6/15頁 |
| 文件大?。?/td> | 186K |
| 代理商： | NCV8842 |
NCV8842
http://onsemi.com
6
APPLICATIONS INFORMATION
THEORY OF OPERATION
V
2
Control
The NCV8842 buck regulator provides a high level of
integration and high operating frequencies allowing the
layout of a switchmode power supply in a very small board
area. This device is based on the proprietary V
2
control
architecture. V
2
control uses the output voltage and its ripple
as the ramp signal, providing an ease of use not generally
associated with voltage or current mode control. Improved
line regulation, load regulation and very fast transient
response are also major advantages.
Figure 3. Buck Converter with V
2
Control.
Buck
Controller
FFB
V
REF
+
Duty Cycle
V
2
Control
Error
Amplifier
PWM
Comparator
R1
Oscillator
+
+
V
O
SFB
V
IN
Latch
R
Slope
Comp
L1
C1
D1
R2
S
V
C
S1
As shown in Figure 3, there are two voltage feedback
paths in V
2
control, namely FFB(Fast Feedback) and
SFB(Slow Feedback). In FFB path, the feedback voltage
connects directly to the PWM comparator. This feedback
path carries the ramp signal as well as the output DC voltage.
Artificial ramp derived from the oscillator is added to the
feedback signal to improve stability. The other feedback
path, SFB, connects the feedback voltage to the error
amplifier whose output V
C
feeds to the other input of the
PWM comparator. In a constant frequency mode, the
oscillator signal sets the output latch and turns on the switch
S1. This starts a new switch cycle. The ramp signal,
composed of both artificial ramp and output ripple,
eventually comes across the V
C
voltage, and consequently
resets the latch to turn off the switch. The switch S1 will turn
on again at the beginning of the next switch cycle. In a buck
converter, the output ripple is determined by the ripple
current of the inductor L1 and the ESR (equivalent series
resistor) of the output capacitor C1.
The slope compensation signal is a fixed voltage ramp
provided by the oscillator. Adding this signal eliminates
subharmonic oscillation associated with the operation at
duty cycle greater than 50%. The artificial ramp also ensures
the proper PWM function when the output ripple voltage is
inadequate. The slope compensation signal is properly sized
to serve it purposes without sacrificing the transient
response speed.
Under load and line transient, not only the ramp signal
changes, but more significantly the DC component of the
feedback voltage varies proportionally to the output voltage.
FFB path connects both signals directly to the PWM
comparator. This allows instant modulation of the duty cycle
to counteract any output voltage deviations. The transient
response time is independent of the error amplifier
bandwidth. This eliminates the delay associated with error
amplifier and greatly improves the transient response time.
The error amplifier is used here to ensure excellent DC
accuracy.
Error Amplifier
The NCV8842 has a transconductance error amplifier,
whose noninverting input is connected to an Internal
Reference Voltage generated from the onchip regulator.
The inverting input connects to the V
FB
pin. The output of
the error amplifier is made available at the V
C
pin. A typical
frequency compensation requires only a 0.1 F capacitor
connected between the V
C
pin and ground, as shown in
Figure 1. This capacitor and error amplifier’s output
resistance (approximately 8.0 M ) create a low frequency
pole to limit the bandwidth. Since V
2
control does not
require a high bandwidth error amplifier, the frequency
compensation is greatly simplified.
The V
C
pin is clamped below Output High Voltage. This
allows the regulator to recover quickly from over current or
short circuit conditions.
Oscillator and Sync Feature
The onchip oscillator is trimmed at the factory and
requires no external components for frequency control. The
high switching frequency allows smaller external
components to be used, resulting in a board area and cost
savings. The tight frequency tolerance simplifies magnetic
components selection. The switching frequency is reduced
to 25% of the nominal value when the V
FB
pin voltage is
below Frequency Foldback Threshold. In short circuit or
overload conditions, this reduces the power dissipation of
the IC and external components.
An external clock signal can sync the NCV8842 to a
higher frequency. The rising edge of the sync pulse turns on
the power switch to start a new switching cycle, as shown in
Figure 4. There is approximately 0.5 s delay between the
rising edge of the sync pulse and rising edge of the V
SW
pin
voltage. The sync threshold is TTL logic compatible, and
相關PDF資料 |
PDF描述 |
|---|---|
| NCV8842MNR2G | 1.5 A, 170 kHz, Buck Regulator with Synchronization Capability |
| NCV8842PWG | 1.5 A, 170 kHz, Buck Regulator with Synchronization Capability |
| NCV8842PWR2G | 1.5 A, 170 kHz, Buck Regulator with Synchronization Capability |
| NCV8843MNR2G | 1.5 A, 340 kHz, Buck Regulator with Synchronization Capability |
| NCV8843PWG | 1.5 A, 340 kHz, Buck Regulator with Synchronization Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV8842_11 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.5 A, 170 kHz, Buck Regulator with Synchronization Capability |
| NCV8842DG | 功能描述:直流/直流開關轉換器 1.5A LOW VOLTAGE REG RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCV8842DR2G | 功能描述:直流/直流開關轉換器 1.5A LOW VOLTAGE REG RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCV8842MNR2G | 功能描述:直流/直流開關轉換器 1.5A LOW VOLTAGE BUCK REG RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCV8842MNR2GEVB | 功能描述:BOARD EVAL FOR NCV8842 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。