- 您現在的位置：買賣IC網 > PDF目錄363237 > NCV8509PDW26 (ON SEMICONDUCTOR) Sequenced Linear Dual-Voltage Regulator PDF資料下載
參數資料
| 型號： | NCV8509PDW26 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Sequenced Linear Dual-Voltage Regulator |
| 中文描述： | DUAL OUTPUT, FIXED POSITIVE REGULATOR, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 123K |
| 代理商： | NCV8509PDW26 |
NCV8509 Series
http://onsemi.com
14
V
OUT1
V
OUT2
Short On
V
OUT1
Short On
V
OUT2
≈
10
μ
s
≈
10
μ
s
Fast SLEW Rate >> Soft Start
Figure 40. Fault Response. Note the High SLEW Rate Coming Out of Fault Conditions.
Soft Start Only Applies to a Power Up Sequence.
Fast SLEW Rate >> Soft Start
Decay Time Dependent
on External Load
Decay Time Dependent
on External Load
Disable Time
Disable Time
Slew Rate Control
Figure 41 shows the circuitry associated with Slew Rate
Control. The diagram highlights the control of one output for
simplicity. V
OUT1
and V
OUT2
are both controlled on the IC.
The slew rate capacitor (C
SLEW
) is charged with an
onchip current source runing at 6.0 A (typ.). Charging a
capacitor with a current source creates a linear voltage ramp
as shown in Figure 42.
The lowest voltage to the positive terminals of the
comparator (Error Amp) dominates the output voltage
(V
OUT
). Consequently, when C
SLEW
is fully discharged on
power up, it is the dominant factor on the positive terminal
and disables the output. The output (V
OUT
) follows the
linear ramp on the SLEW pin (after being gained up with R1
and R2) until V
BG
becomes the dominant voltage. This
occurs when SLEW = V
BG
+ V
D1
or approximately 1.8 V.
R1
+
+
V
OUT
R2
Error Amp
SLEW
C
SLEW
6.0
μ
A
Internal
Voltage
Rail
≈
3.8 V
D2
V
IN1
D1
V
BG
Figure 41. Slew Control Circuitry
Slew time can be calculated using the standard capacitor
equation.
Cdt, t
Using a 33 nF capacitor, the slew time is:
(33 nF)(1.8 V)
6 A
The corresponding slew rate for this is 1.8 V/9.9 ms =
182 V/s ON THE SLEW PIN.
To calculate the slew rate on outputs, you must multiply
by the gain set up by R1 and R2.
VOUT
1.28 V
For a 5 V output, the gain would be:
5 V
1.28 V
assuming V
BG
= 1.28 V.
The resultant slew rate on the output is the slew rate on the
SLEW pin multiplied by the gain, or:
(182 V s)
(3.9 V V)
I
C( V)
I
t
9.9 ms
Av
Av
3.9 V V
710 V s
Outputs in Regulation
Figure 42.
Time (ms)
S
3.8
1.8
t
SLEW
相關PDF資料 |
PDF描述 |
|---|---|
| NCV8509PDW26R2 | Sequenced Linear Dual-Voltage Regulator |
| NCV8512 | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV8512PW50G | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV8512PW50R2G | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV8664 | Ultra−Low Iq Low Dropout Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV8509PDW26G | 功能描述:線性穩壓器 - 標準 2.6V 100mA Sequenced Dual RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| NCV8509PDW26R2 | 功能描述:線性穩壓器 - 標準 2.6V 100mA Sequenced RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| NCV8509PDW26R2G | 功能描述:線性穩壓器 - 標準 2.6V 100mA Sequenced Dual RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| NCV8512 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV8512PW50G | 功能描述:低壓差穩壓器 - LDO 5V MICROPOWER 150mA LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。