- 您現在的位置：買賣IC網 > PDF目錄363234 > NCV7701 (ON SEMICONDUCTOR) 2.0 Amp H-Bridge Driver(2A,H橋驅動器) PDF資料下載
參數資料
| 型號： | NCV7701 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | 2.0 Amp H-Bridge Driver(2A,H橋驅動器) |
| 中文描述： | 2.0安培H橋驅動器（甲，魔橋驅動器） |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 53K |
| 代理商： | NCV7701 |
NCV7701
http://onsemi.com
4
Table 1. HBridge Mode Control
EN
IN1
IN2
HBridge
OUTA
OUTB
0
X
X
Off (Sleep Mode)
Off
Off
1
0
0
Brake Low
Low
Low
1
0
1
Forward
High
Low
1
1
0
Reverse
Low
High
1
1
1
Brake High
High
High
Table 2. Fault Diagnostics
Fault Condition
Fault Pin
HBridge
No Faults
High Z
Normal Operation
Undervoltage
Low
Off
Overvoltage
Low
Off
Thermal Shutdown
Low
Off
Current Limit
Low
1 or more Drivers in
Current Limit
PACKAGE PIN DESCRIPTION
Pin No.
Symbol
Description
1
V
BAT
IC supply voltage.
2, 9, 10, 19, 20
NC
No connection.
3
OUTB
Bridge output.
4, 5, 6, 7, 14, 15, 16, 17
GND
Power ground.
8
FAULT
Diagnostic output.
11
IN2
Mode control input.
12
IN1
Mode control input.
13
EN
Chip enable.
18
OUTA
Bridge output.
Operating Description
During power up, the outputs are HIZ regardless of the
input states. When the undervoltage lockout threshold is
exceeded, the outputs will reflect the input states. Outputs
change to HIZ whenever an undervoltage, overvoltage or
thermal shutdown fault is detected. Normal operation will
resume when faults are resolved.
Overcurrent Protection
Current is monitored continuously in each switch of each
half bridge when the ENA input is in a high state thus
protecting each switch from faults due to short to GND,
short to V
BAT
or shorted load conditions. Only the affected
halfbridge is disabled for short to V
BAT
or short to GND
faults. A mask timer is initiated after a fault is detected and
prevents recognition of an overcurrent event until the mask
time expires. Persistence of an overcurrent condition causes
the bridge output to change to HIZ and the FAULT output
to latch low until the next transition occurs on either the
input related to the faulted output or the ENA input is
brought low then high again. This method of protection
provides current limiting on a cyclebycycle basis and
helps allow a stall torque current to be ignored during motor
start. Continued overcurrent may eventually result in
activation of the thermal shutdown circuitry, thus activating
a second level of protection for the NCV7701.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV7701DW | 2.0 Amp H-Bridge Driver |
| NCV7702B | 1 A Dual H-Bridge Driver(1A雙H橋驅動器) |
| NCV7805BD2T* | 1.0A Positive Voltage Regulators |
| NCV7805BD2TG* | 1.0A positive vlotage regulators |
| NCV7805BD2TR4* | 1.0A positive vlotage regulators |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV7701/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:2.0 Amp H-Bridge Driver |
| NCV7701DW | 功能描述:IC DRIVER H-BRIDGE 2A 20SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐，1.6 歐姆 電流 - 輸出 / 通道:205mA，410mA 電流 - 峰值輸出:500mA，1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR) |
| NCV7701DWR2 | 功能描述:IC DRIVER H-BRIDGE 2A 20SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐，1.6 歐姆 電流 - 輸出 / 通道:205mA，410mA 電流 - 峰值輸出:500mA，1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR) |
| NCV7701DWR2G | 制造商:ON Semiconductor 功能描述:MOSFET DRVR 1A DUAL LO SIDE H BRDG 20SOIC - Tape and Reel |
| NCV7702B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1 A Dual H−Bridge Driver |
發布緊急采購，3分鐘左右您將得到回復。