- 您現在的位置：買賣IC網 > PDF目錄9885 > NCV7341D21G (ON Semiconductor)TXRX CAN HS LOW POWER 14SOIC PDF資料下載
參數資料
| 型號： | NCV7341D21G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 18/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX CAN HS LOW POWER 14SOIC |
| 標準包裝： | 55 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
NCV7341
http://onsemi.com
9
transmissions, an internal bus failure flag is set and made
immediately visible through a Low level on the ERR pin.
The transmission and reception circuitry continues to
function.
When four consecutive dominant transmissions succeed
without a bus line short being detected, the internal bus
failure flag is reset and ERR pin is released to High level.
Split Circuit
The VSPLIT Pin is operational only in normal and
receiveonly modes. It is floating in standby and sleep
modes. The VSPLIT can be connected as shown in Figure 2
and Figure 3 and its purpose is to provide a stabilized DC
voltage of VCC/2 to the bus avoiding possible steps in the
commonmode signal, therefore reducing EME. These
unwanted steps could be caused by an unpowered node on
the network with excessive leakage current from the bus that
shifts the recessive voltage from its nominal VCC/2 level.
Wakeup
The transceiver can detect wakeup events in standby,
gotosleepand sleep modes. Two types of wakeup events
are handled – remote wakeup via the CAN bus or a local
wakeup via the WAKE pin. A valid remote wakeup is
recognized after two dominant states of the CAN bus of at
least tdom, each of them followed by a recessive state of at
least trec.
A local wakeup is detected after a change of state (High
to Low, or Low to High) on WAKE Pin which is stable for
at least tWAKE. To increase the EMS level of the WAKE Pin,
an internal current source is connected to it. If the state of the
WAKE Pin is stable at least for tWAKE, the direction of the
current source follows (pulldown current for Low state,
pullup current for High state). It is recommended to connect
Pin WAKE either to GND or VBAT if it’s not used in the
application.
Fail Safe Features
Fail safe behavior is ensured by the detection functions
associated with the internal flags.
Furthermore, a currentlimiting circuit protects the
transmitter output stage from damage caused by accidental
short circuit to either positive or negative supply voltage,
although power dissipation increases during this fault
condition.
The Pins CANH and CANL are protected from
automotive electrical transients (according to ISO 7637; see
Figure 9). Pins TxD is pulled high and Pins STB and EN are
pulled low internally should the input become disconnected.
Pins TxD, STB, EN and RxD will be floating, preventing
reverse supply should the VIO supply be removed.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B20-MW-F1 | CONVERTER MOD DC/DC 5V 100W |
| MS3102A32-6PX | CONN RCPT 23POS BOX MNT W/PINS |
| VE-J3D-MX-F4 | CONVERTER MOD DC/DC 85V 75W |
| VI-2WK-MX-F4 | CONVERTER MOD DC/DC 40V 75W |
| VE-J3D-MX-F3 | CONVERTER MOD DC/DC 85V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV7341D21R2G | 功能描述:網絡控制器與處理器 IC HS LP CAN TRANSC. RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| NCV7342 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Speed Low Power CAN Transceiver |
| NCV7342D10R2G | 制造商:ON Semiconductor 功能描述:HS LP CAN TRANSC (L-WU) - Tape and Reel 制造商:ON Semiconductor 功能描述:IC TXRX CAN SGL WIRE 制造商:ON Semiconductor 功能描述:REEL - HS LP CAN TRANSC (L-WU) |
| NCV7342D13R2G | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Speed Low Power CAN Transceiver |
| NCV7356 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Single Wire CAN Transceiver |
發布緊急采購，3分鐘左右您將得到回復。