- 您現在的位置：買賣IC網 > PDF目錄361105 > NCV51411 (ON SEMICONDUCTOR) 1.5A, 260kHz, Low Voltage Buck Regulator with Synchronization Capability(具有同步能力的1.5A, 260kHz,低壓降壓調整器) PDF資料下載
參數資料
| 型號： | NCV51411 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | 1.5A, 260kHz, Low Voltage Buck Regulator with Synchronization Capability(具有同步能力的1.5A, 260kHz,低壓降壓調整器) |
| 中文描述： | 1.5A的，260kHz，低電壓降壓穩壓器與同步功能（具有同步能力的1.5A的，260kHz，低壓降壓調整器） |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 181K |
| 代理商： | NCV51411 |
NCV51411
http://onsemi.com
8
BOOST Pin
The BOOST pin provides base driving current for the
power switch. A voltage higher than V
IN
provides required
headroom to turn on the power switch. This in turn reduces
IC power dissipation and improves overall system
efficiency. The BOOST pin can be connected to an external
booststrapping circuit which typically uses a 0.1 F capacitor
and a 1N914 or 1N4148 diode, as shown in Figure 1. When the
power switch is turned on, the voltage on the BOOST pin is
equal to
VBOOST
VIN
VO
VF
where:
V
F
= diode forward voltage.
The anode of the diode can be connected to any DC
voltage as well as the regulated output voltage (Figure 1).
However, the maximum voltage on the BOOST pin shall not
exceed 40 V.
As shown in Figure 7, the BOOST pin current includes a
constant 7.0 mA predriver current and base current
proportional to switch conducting current. A detailed
discussion of this current is conducted in Thermal
Consideration section. A 0.1
adequate for maintaining the Boost pin voltage during the on
time.
F capacitor is usually
Figure 7. The Boost Pin Current Includes 7.0 mA
PreDriver Current and Base Current when the
Switch is Turned On. The Beta Decline of the
Power Switch Further Increases the Base
Current at High Switching Current
0
0.5
SWITCHING CURRENT (A)
1.0
1.5
B
0
5
10
15
20
25
30
Shutdown
The internal power switch will not turn on until the V
IN
pin rises above the Startup Voltage. This ensures no
switching will occur until adequate supply voltage is
provided to the IC.
The IC enters a sleep mode when the SHDNB pin is pulled
below the Shutdown Threshold Voltage. In sleep mode, the
power switch is kept open and the supply current reduces to
Shutdown Quiescent Current. This pin has an internal
pullup current. When restarting the IC, the SHDNB pin
should be returned to an open condition insuring discharge
of the Comp pin and proper softstart. If the SHDNB pin is
forced high to restart the IC, the Comp pin will not be pulled
low internally and softstart may not occur.
Startup
During power up, the regulator tends to quickly charge up
the output capacitors to reach voltage regulation. This gives
rise to an excessive inrush current which can be detrimental
to the inductor, IC and catch diode. In V
2
control , the
compensation capacitor provides SoftStart with no need
for extra pin or circuitry. During the power up, the Output
Source Current of the error amplifier charges the
compensation capacitor which forces V
C
pin and thus output
voltage ramp up gradually. The SoftStart duration can be
calculated by
TSS
VC
CCOMP
ISOURCE
where:
V
C
= V
C
pin steadystate voltage, which is approximately
equal to error amplifier’s reference voltage.
C
COMP
= Compensation capacitor connected to the V
C
pin
I
SOURCE
= Output Source Current of the error amplifier.
Using a 0.1 F C
COMP
, the calculation shows a T
SS
over
5.0 ms which is adequate to avoid any current stresses.
Figure 8 shows the gradual rise of the V
C
, V
O
and envelope
of the V
SW
during power up. There is no voltage overshoot
after the output voltage reaches the regulation. If the supply
voltage rises slower than the V
C
pin, output voltage may
overshoot.
Figure 8. The Power Up Transition of NCV51411
Regulator
相關PDF資料 |
PDF描述 |
|---|---|
| NCV5500 | 500 mA Linear Regulator(500mA線性穩壓器) |
| NCV5501 | 500 mA Linear Regulator(500mA線性穩壓器) |
| NCV78L05A | 100 mA Positive Voltage Regulators(三端小電流正固定電壓穩壓器) |
| NCV8184DT | Micropower 70 mA Low Dropout Tracking Regulator/Line Driver |
| NCV8184DTRK | Micropower 70 mA Low Dropout Tracking Regulator/Line Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV51411DR2 | 功能描述:直流/直流開關轉換器 1.5A Low Voltage RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCV51411DR2G | 功能描述:直流/直流開關轉換器 1.5A Low Voltage Buck RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCV51411MNR2 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.5 A, 260 kHz, Low Voltage Buck Regulator with Synchronization Capability |
| NCV51411MNR2G | 功能描述:直流/直流開關轉換器 BUCK REGULATOR RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCV51411PWR2 | 功能描述:直流/直流開關轉換器 1.5A Low Voltage RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。