- 您現在的位置：買賣IC網 > PDF目錄363234 > NCV4279BDW (ON SEMICONDUCTOR) 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG PDF資料下載
參數資料
| 型號： | NCV4279BDW |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| 中文描述： | 5 V FIXED POSITIVE LDO REGULATOR, 0.6 V DROPOUT, PDSO20 |
| 封裝： | SO-20 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 102K |
| 代理商： | NCV4279BDW |
NCV4279B
http://onsemi.com
7
CIRCUIT DESCRIPTION
REGULATOR CONTROL FUNCTIONS
The NCV4279B contains the microprocessor compatible
control function RESET (Figure 11).
Figure 11. Reset and Delay Circuit Wave Forms
V
IN
V
OUT
RESET
DELAY
(V
DT
)
Threshold
DELAY
Threshold
RESET
T
d
T
d
RESET Function
A RESET signal (low voltage) is generated as the IC
powers up until V
OUT
is within 6.0% of the regulated output
voltage, or when V
OUT
drops out of regulation,and is lower
than 8.0% below the regulated output voltage. Hysteresis is
included in the function to minimize oscillations.
The RESET output is an open collector NPN transistor,
controlled by a low voltage detection circuit. The circuit is
functionally independent of the rest of the IC thereby
guaranteeing that the RESET signal is valid for V
OUT
as low
as 1.0 V.
Adjustable Reset Function
The reset threshold can be made lower by connecting an
external resistor divider to the R
ADJ
lead from the V
OUT
lead, as displayed in Figure 12. This lead is grounded to
select the default value of 4.6 V.
Figure 12. Adjustable RESET
R
ADJ
to
μ
P and
System
Power
R
RST
V
OUT
C
OUT
RESET
C
DELAY
Delay
NCV4279B
to
μ
P and
RESET
Port
DELAY Function
The reset delay circuit provides a programmable (by
external capacitor) delay on the RESET output lead.
The DELAY lead provides source current (typically
2.5 A) to the external DELAY capacitor during the
following proceedings:
1. During Power Up (once the regulation threshold
has been verified).
2. After a reset event has occurred and the device is
back in regulation. The DELAY capacitor is
discharged when the regulation (RESET threshold)
has been violated. This is a latched incident. The
capacitor will fully discharge and wait for the
device to regulate before going through the delay
time event again.
FLAG/Monitor Function
An onchip comparator is provided to perform an early
warning to the microprocessor of a possible reset signal. The
reset signal typically turns the microprocessor off
instantaneously. This can cause unpredictable results with
the microprocessor. The signal received from the FLAG pin
will allow the microprocessor time to complete its present
task before shutting down. This function is performed by a
comparator referenced to the bandgap reference. The actual
trip point can be programmed externally using a resistor
divider to the input monitor (MON) (Figure 13). The typical
threshold is 1.20 V on the MON Pin.
Figure 13. FLAG/Monitor Function
V
BAT
V
IN
MON
V
OUT
C
OUT
V
CC
I/O
RESET
μ
P
FLAG
RESET
GND
Delay
NCV4279B
R
ADJ
相關PDF資料 |
PDF描述 |
|---|---|
| NCV4279BDWR2 | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV4279BD1 | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV4279BD1R2 | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV4279BD2 | 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG |
| NCV4299 | 5.0V Low Drop Fixed Voltage Regulator(5.0V，低壓差固定電壓穩壓器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV4279BDWG | 功能描述:低壓差穩壓器 - LDO ANA 5.0V MICROPOWER RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCV4279BDWR2 | 功能描述:低壓差穩壓器 - LDO ANA 5.0V MICROPOWER RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCV4279BDWR2G | 功能描述:低壓差穩壓器 - LDO ANA 5.0V MICROPOWER RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| NCV4279CD2R2G | 制造商:ON Semiconductor 功能描述:150MA LDO LINEAR REGULATOR, PB FREE - Tape and Reel |
| NCV4279D1 | 功能描述:低壓差穩壓器 - LDO 5V 150mA MicroPower RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。