參數資料
型號： NCV4269
廠商： ON SEMICONDUCTOR
英文描述： 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Sense Output(帶有延遲，可調復位和檢測輸出功能的5.0V，微功率150mA LDO線性穩壓器)
中文描述： 5.0V的微一百五十毫安LDO線性穩壓器的延遲，可調復位和檢測輸出（帶有延遲，可調復位和檢測輸出功能的5.0V，150mA的微功率LDO的線性穩壓器）
文件頁數： 10/15頁
文件大?。?/td> 140K
代理商： NCV4269
NCV4269
http://onsemi.com
10
APPLICATION DESCRIPTION
OUTPUT REGULATOR
The output is controlled by a precision trimmed reference.
The PNP output has base drive quiescent current control for
regulation while the input voltage is low, preventing over
saturation. Current limit and voltage monitors complement
the regulator design to give safe operating signals to the
processor and control circuits.
RESET OUTPUT (RO)
A reset signal, Reset Output, RO, (low voltage) is
generated as the IC powers up. After the output voltage V
Q
increases above the reset threshold voltage V
RT
, the delay
timer D is started. When the voltage on the delay timer V
D
passes V
UD
, the reset signal RO goes high. A discharge of
the delay timer V
D
is started when V
Q
drops and stays below
the reset threshold voltage V
RT
. When the voltage of the
delay timer V
D
drops below the lower threshold voltage V
LD
the reset output voltage V
RO
is brought low to reset the
processor.
The reset output RO is an open collector NPN transistor
with an internal 20 k pullup resistor connected to the
output Q, controlled by a low voltage detection circuit. The
circuit is functionally independent of the rest of the IC,
thereby guaranteeing that RO is valid for V
Q
as low as 1.0 V.
RESET ADJUST (R
ADJ
)
The reset threshold V
RT
can be decreased from a typical
value of 4.65 V to as low as 3.5 V by using an external
voltage divider connected from the Q lead to the pin RADJ,
as shown in Figure 21. The resistor divider keeps the voltage
above the V
RADJ,TH
(typical 1.35 V) for the desired input
voltages, and overrides the internal threshold detector.
Adjust the voltage divider according to the following
relationship:
VRT
VRADJ,TH
(RADJ1
RADJ2) RADJ2
(eq. 1)
If the reset adjust option is not needed, the R
ADJ
pin
should be connected to GND causing the reset threshold to
go to its default value (typically 4.65 V).
RESET DELAY (D)
The reset delay circuit provides a delay (programmable by
capacitor C
D
) on the reset output lead RO. The delay lead D
provides charge current I
D
(typically 6.5 A) to the external
delay capacitor C
D
during the following times:
1. During Powerup (once the regulation threshold has
been exceeded).
2. After a reset event has occurred and the device is
back in regulation. The delay capacitor is set to
discharge when the regulation (V
RT
, reset
threshold voltage) has been violated. When the
delay capacitor discharges to V
LD
, the reset signal
RO pulls low.
SETTING THE DELAY TIME
The delay time is set by the delay capacitor C
D
and the
charge current I
D
. The time is measured by the delay
capacitor voltage charging from the low level of V
DSAT
to
the higher level V
UD
. The time delay follows the equation:
td
[CD(VUD
VDSAT)] ID
(eq. 2)
Example:
Using C
D
= 100 nF.
Use the typical value for V
DSAT
= 0.1 V.
Use the typical value for V
UD
= 1.8 V.
Use the typical value for Delay Charge Current I
D
= 6.5 A.
td
[100 nF(1.8
0.1 V)] 6.5 A
26.2 ms
(eq. 3)
Q
GND
I
R
ADJ
NCV4269
C
Q
**
10 F
RO
0.1 F
M
D
C
D
V
BAT
V
DD
SO
Figure 21. Application Diagram
SI
I/O
I/O
R
ADJ2
R
ADJ1
R
SI1
R
SI2
C
I
*
*C
I
required if regulator is located far from the power supply filter.
** C
Q
required for Stability. Cap must operate at minimum temperature expected.
相關PDF資料
PDF描述
NCV4274 400 mA 2% and 4%Voltage Regulator Family(400mA 2%和4%穩壓器系列)
NCV4274A 400 mA 2% and 4%Voltage Regulator Family(400mA 2%和4%穩壓器系列)
NCV4275 5.0V, 450mA Low Drop Voltage Regulator(5.0V, 450mA低壓差穩壓器)
NCV4279B 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG
NCV4279BDW 5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Monitor FLAG
相關代理商/技術參數
參數描述
NCV4269_07 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Sense Output
NCV4269A 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:5.0 V Micropower 150 mA LDO Linear Regulator with DELAY, Adjustable RESET, and Sense Output
NCV4269AD133R2G 制造商:ON Semiconductor 功能描述:3.3V 150MA LDO - Tape and Reel 制造商:ON Semiconductor 功能描述:IC REG LDO 3.3 150MA 制造商:ON Semiconductor 功能描述:REEL / 3.3V 150MA LDO
NCV4269AD150G 功能描述:低壓差穩壓器 - LDO 5.0V 150MA LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
NCV4269AD150R2G 功能描述:低壓差穩壓器 - LDO 5.0V 150MA LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*