- 您現在的位置：買賣IC網 > PDF目錄363233 > NCV1124 (ON SEMICONDUCTOR) Dual Variable-Reluctance Sensor Interface IC(雙可變磁阻傳感器接口電路) PDF資料下載
參數資料
| 型號： | NCV1124 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Dual Variable-Reluctance Sensor Interface IC(雙可變磁阻傳感器接口電路) |
| 中文描述： | 雙可變磁阻傳感器接口IC（雙可變磁阻傳感器接口電路） |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 172K |
| 代理商： | NCV1124 |
NCV1124
http://onsemi.com
4
THEORY OF OPERATION
NORMAL OPERATION
Figure 2 shows one channel of the NCV1124 along with
the necessary external components. Both channels share the
IN
Adj
pin as the negative input to a comparator. A brief
description of the components is as follows:
V
RS
Ideal sinusoidal, ground referenced, sensor output
amplitude usually increases with frequency, depending on
loading.
R
RS
Source impedance of sensor.
R1/R
Adj
External resistors for current limiting and
biasing.
INP1/IN
Adj
Internal current sources that determine trip
points via R1/R
Adj
.
COMP1
Internal comparator with builtin hysteresis
set at 160 mV.
OUT1
Output 0 V 5.0 V square wave with the same
frequency as V
RS
.
By inspection, the voltage at the (+) and () terminals of
COMP1 with V
RS
= 0V are:
V+
INP1(R1
RRS)
(1)
V
INAdj
RAdj
(2)
As V
RS
begins to rise and fall, it will be superimposed on
the DC biased voltage at V
+
.
V+
INP1(R1
RRS)
VRS
(3)
To get comparator COMP1 to trip, the following
condition is needed when crossing in the positive direction,
V+
V
VHYS
(4)
(V
HYS
is the builtin hysteresis set to 160 mV), or when
crossing in the negative direction,
V+
V
VHYS
(5)
Combining equations 2, 3, and 4, we get:
INP1(R1
RRS)
VRS
INAdj
RAdj
VHYS
(6)
therefore,
VRS(+TRP)
INAdj
RAdj
INP1(R1
RRS)
VHYS
(7)
It should be evident that tripping on the negative side is:
VRS(TRP)
INAdj
RAdj
INP1(R1
RRS)
VHYS
(8)
In normal mode,
INP1
INAdj
(9)
We can now rewrite equation (7) as:
VRS(+TR)
INP1(RAdj
R1
RRS)
VHYS
(10)
By making
RAdj
R1
RRS
(11)
you can detect signals with as little amplitude as V
HYS
.
A design example is given in the applications section.
OPEN SENSOR PROTECTION
The NCV1124 has a DIAG pin that when pulled high (5.0
V), will increase the IN
Adj
current source by roughly 50%.
Equation (7) shows that a larger V
RS(+TRP)
voltage will be
needed to trip comparator COMP1. However, if no V
RS
signal is present, then we can use equations 1, 2, and 4
(equation 5 does not apply in this mode) to get:
INP1(R1
RRS)
INP1
KI
RAdj
VHYS
(12)
Since R
RS
is the only unknown variable we can solve for
R
RS
,
RRS
INP1
KI
RAdj
INP1
VHYS
R1
(13)
Equation (13) shows that if the output switches states
when entering the diag mode with V
RS
= 0, the sensor
impedance must be greater than the above calculated value.
This can be very useful in diagnosing intermittent sensor.
INPUT PROTECTION
As shown in Figure 2, an active clamp is provided on each
input to limit the voltage on the input pin and prevent
substrate current injection. The clamp is specified to handle
±
12 mA. This puts an upper limit on the amplitude of the
sensor output. For example, if R1 = 20 k, then
VRS(MAX)
20 k
12 mA
240 V
Therefore, the V
RS(pkpk)
voltage can be as high as 480 V.
The NCV1124 will
typically
run at a frequency up to 1.8
MHz if the input signal does not activate the positive or
negative input clamps. Frequency performance will be
lower when the positive or negative clamps are active.
Typical
performance will be up to a frequency of 680 kHz
with the clamps active.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV2574 | 0.5 A, Adjustable Output Voltage, Step-Down Switching Regulator(0.5A,可調輸出電壓,降壓型開關穩壓器) |
| NCV2904DR2 | DUAL DIFFERENTIAL INPUT OPERATIONAL AMPLIFIERS |
| NCV2931 | 100 mA, Adjustable Output, LDO Voltage Regulator with 60 V Load Dump Protection(100mA，可調輸出，帶有60V負載保護的低壓差穩壓器) |
| NCV2951 | 100 mA, Low Power Low Dropout Voltage Regulator(100mA，低功耗低壓差穩壓器) |
| NCV33033 | Brushless DC Motor Controller(無刷直流電機控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV1124DG | 功能描述:接口 - 專用 Dual Variable RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| NCV1124DR2G | 功能描述:接口 - 專用 DUAL VARIABLE RELUCTANCE RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| NCV1406SNT1G | 功能描述:直流/直流開關轉換器 STEP-UP DC-DC CONVERTER RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCV1413B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Voltage, High Current Darlington Transistor Arrays |
| NCV1413BDR2 | 功能描述:達林頓晶體管 High Voltage High RoHS:否 制造商:Texas Instruments 配置:Octal 晶體管極性:NPN 集電極—發射極最大電壓 VCEO:50 V 發射極 - 基極電壓 VEBO: 集電極—基極電壓 VCBO: 最大直流電集電極電流:0.5 A 最大集電極截止電流: 功率耗散: 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-18 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。