參數資料
型號： NCP802
廠商： ON SEMICONDUCTOR
英文描述： Highly Integrated Lithium Battery Protection Circuit for One Cell Battery Packs
中文描述： 高度集成的鋰電池保護電路的一個電池組
文件頁數： 18/23頁
文件大?。?/td> 125K
代理商： NCP802
NCP802
http://onsemi.com
18
Undervoltage Detection
The undervoltage detector (VD2) monitors the VCELL
pin voltage. When the VCELL voltage crosses the
undervoltage threshold (VDET2) from a high value to a
value lower than VDET2, VD2 senses an undervoltage
condition, and an external, discharge control, Nchannel
MOSFET turns off by driving the DO pin to its low level.
The low level of DO is set to GND and the high level to
VCELL.
To reset the DO pin to its high level, one must connect a
charger to the battery pack. While the VCELL voltage
remains under VDET2, chargecurrent can flow through the
parasitic diode of the external discharge control MOSFET.
Once the VCELL voltage rises above VDET2, the NCP802
drives DO high. Connecting a charger to the battery pack
drives the DO level high instantaneously when the VCELL
voltage is higher than VDET2. VD2 has no hysteresis.
After VD2 detects an undervoltage condition, the
NCP802 enters a low supply current, standby mode.
Maximum standby current equals 0.1 A at VCELL equal
to 2.0 V. An internal pullup disables all the device functions
and thus drastically lowers quiescent current. When the
charger connects to the battery, it pulls small levels of
current from the P pin. This overcomes the internal pullup
and allows the NCP802 to reset.
There are internal, fixed delay times for both the detection
and release from an undervoltage condition. If the fault or
reset conditions are shorter than their respective delay times,
the NCP802 ignores that condition and stays in its previous
state.
Excess DischargeCurrent/Short Circuit Detection
The excess dischargecurrent detector (VD3) and the
short circuit detector can function when the control
MOSFET’s are on. When the P pin voltage is below the
short circuit detection voltage (VSHORT) and above the
excess dischargecurrent threshold (VDET3), VD3
operates. When the P pin voltage rises higher than
VSHORT, the NCP802 enables the short circuit detector.
When either detector activates, the NCP802 turns off an
external, discharge control, Nchannel, MOSFET by
driving the DO pin to its low level.
The output delay time for the excess dischargecurrent
detector is internally fixed. If the P pin, voltage level
recovers from a level between VSHORT and VDET3 within
the delay time, the discharge MOSFET stays in its high state.
Output delay time for release from excess dischargecurrent
detection is typically 1.2 ms. When the short circuit detector
activates, DO transitions to its low state after a delay time of
approximately 400 s.
There is an integrated pulldown resistor (RSHORT)
connected between the P and GND pins. After VD3 or the
short circuit detector has activated; removing the cause of
that activation turns the discharge MOSFET back on. This
occurs because RSHORT pulls the P pin, voltage level
down to the GND pin, voltage level. The NCP802 internally
disconnects RSHORT during a normal, faultfree, state. The
NCP802 only connects RSHORT if it has detected an excess
dischargecurrent or short circuit fault. In other words, VD3
is automatically released from excess dischargecurrent and
short circuit faults when the user removes the load.
The output delay time of excess dischargecurrent
detection is set shorter than the delay time for undervoltage
detection. Therefore, if VCELL voltage drops below
VDET2 during an excess dischargecurrent or short circuit
fault, the NCP802 detects the current fault first. This
prevents large discharge current faults from activating the
undervoltage detector and putting the NCP802 into standby
mode. Standby mode requires the charger to reset the
NCP802, while excess dischargecurrent and short circuit
faults only require that the fault be removed.
Excess ChargeCurrent Detection
When the battery pack is chargeable and discharge is also
possible, VD4 senses the P pin voltage. For example, if the
user connects the battery to an inappropriate charger, excess
current can flow. Then, the P voltage drops below the
excess chargecurrent threshold (VDET4). Next, the output
of CO becomes low. This prevents excess current flow into
the circuit by turning off the external MOSFET.
The output delay of the excess chargecurrent detector is
internally fixed. If the fault condition is within the delay time
window, the detector will not sense it and the MOSFET will
not change state. VD4 can be released by disconnecting a
charger and applying a load.
Delay Shortening Function
The output delay time of overcharge, overdischarge,
excess dischargecurrent, excess chargecurrent, and the
release from those detecting modes can be made shorter than
the preset value by forcing the VCELL voltage to the DS
pin. When one forces the specified middle range voltage to
the DS pin, the output delay circuit becomes disabled.
Therefore, under this condition, when overcharge or excess
charge current is detected, output level can be checked
without waiting for the delay.
A 1.3 M pulldown resistor is connected between DS
pin and GND internally. For normal operation, the DS pin
should be at no connection state.
Zero Battery Voltage Charging
If the charger voltage is equal or higher than the zerovolt
charge, minimum voltage (VST), the NCP802 drives the CO
pin high. Therefore, it allows charging for batteries as low
as zero volts.
相關PDF資料
PDF描述
NCP9001 1.5 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter
NCP9001SNT1G 1.5 MHz, 600 mA, High−Efficiency, Low Quiescent Current, Adjustable Output Voltage Step−Down Converter
NCP9002 1.3 Watt Audio Power Amplifier with Fast Turn On Time
NCP9003 Compact Backlight LED Boost Driver
NCP9003SNT1G Compact Backlight LED Boost Driver
相關代理商/技術參數
參數描述
NCP802/D 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Highly Integrated Lithium Battery Protection Circuit for One Cell Battery Packs
NCP802SAN1T1 功能描述:IC L-I BATTERY PROTECTOR 6SON RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
NCP802SAN1T1G 功能描述:IC L-I BATTERY PROTECTOR 6SON RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
NCP802SAN5T1 功能描述:IC L-I BATTERY PROTECTOR 6SON RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT
NCP802SAN5T1G 制造商:ON Semiconductor 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*