- 您現在的位置：買賣IC網 > PDF目錄361099 > NCP1651DR2 (ON SEMICONDUCTOR) Single Stage Power Factor Controller PDF資料下載
參數資料
| 型號： | NCP1651DR2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | Single Stage Power Factor Controller |
| 中文描述： | POWER FACTOR CONTROLLER, 250 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | SO-16 |
| 文件頁數： | 5/8頁 |
| 文件大小： | 57K |
| 代理商： | NCP1651DR2 |
NCP345
http://onsemi.com
5
APPLICATION INFORMATION
+
OUT
IN
V
ref
GND
CNTRL
+
V
CC
Logic
FET
Driver
Undervoltage
Lock Out
LOAD
AC/DC Adapter or
Accessory Charger
Zener
Diode
(optional)
C1
Schottky
Diode
Microprocessor
port
PCH
NCP345
Zener
Diode
(optional)
Figure 8.
Introduction
In many electronic products, an external AC/DC wall
adapter is used to convert the AC line voltage into a
regulated DC voltage or a current limited source. Line
surges or faults in the adapter may result in overvoltage
events that can damage sensitive electronic components
within the product. This is becoming more critical as the
operating voltages of many integrated circuits have been
lowered due to advances in submicron silicon lithography.
In addition, portable products with removable battery packs
pose special problems since the pack can be removed at any
time. If the user removes a pack in the middle of charging,
a large transient voltage spike can occur which can damage
the product. Finally, damage can result if the user plugs in
the wrong adapter into the charging jack. The challenge of
the product designer is to improve the robustness of the
design and avoid situations where the product can be
damaged due to unexpected, but unfortunately, likely
events that will occur as the product is used.
Circuit Overview
To address these problems, the protection system above
has been developed consisting of the NCP345 Over Voltage
Protection IC and a Pchannel MOSFET switch such as the
MGSF3441. The NCP345 monitors the input voltage and
will not turn on the MOSFET unless the input voltage is
within a safe operating window that has an upper limit of
7.05 V. A zener diode can be placed in parallel to the load to
provide for secondary protection during the brief time that
it takes for the NCP345 to detect the overvoltage fault and
disconnect the MOSFET. The decision to use this secondary
diode is a function of the charging currents expected, load
capacitance across the battery, and the desired protection
voltage by analyzing the dV/dT rise that occurs during the
brief time it takes to turnoff the MOSFET. For battery
powered applications, a lowforward voltage Schottky
diode such as the MBRM120LT3 can be placed in series
with the MOSFET to block the body diode of the MOSFET
and prevent shorting the battery out if the input is
accidentally shorted to ground. This provides additional
voltage margin at the load since there is a small forward drop
across this diode that reduces the voltage at the load.
When the protection circuit turns off the MOSFET, there
can be a sudden rise in the input voltage of the device. This
transient can be quite large depending on the impedance of
the supply and the current being drawn from the supply at the
time of an overvoltage event. This inductive spike can be
clamped with a zener diode from IN to ground. This diode
breakdown voltage should be well above the worst case
supply voltage provided from the AC/DC adapter or
Cigarette Lighter Adapter (CLA), since the zener is only
intended to clamp the transient. The NCP345 is designed so
that the IN and V
CC
pin can safely protect up to 25 V and
withstand transients to 30 V. Since these spikes can be very
narrow in duration, it is important to use a high bandwidth
probe and oscilloscope when prototyping the product to
verify the operation of the circuit under all the transient
conditions. A similar problem can result due to contact
bounce as the DC source is plugged into the product.
For portable products it is normal to have a capacitor to
ground in parallel with the battery. If the product has a
battery pack that is easily removable during charging, this
scenario should be analyzed. Under that situation, the
charging current will go into the capacitor and the voltage
may rise rapidly depending on the capacitor value, the
charging current and the power supply response time.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1651 | Single Stage Power Factor Controller |
| NCP1651DR2G | Single Stage Power Factor Controller |
| NCP345SNT1G | Overvoltage Protection IC |
| NCP346SN1T1G | Overvoltage Protection IC |
| NCP346SN2T1G | Overvoltage Protection IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1651DR2G | 功能描述:功率因數校正 IC Single Stage PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1652ADR2G | 功能描述:功率因數校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1652DR2G | 功能描述:功率因數校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1652DWR2G | 功能描述:功率因數校正 IC ANA PFC CONTROLLER RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| NCP1652L48VGEVB | 功能描述:電源管理IC開發工具 100W PFC 48V FIXED VOLTAGE RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。