參數資料
型號: NCP1395BPG
廠商: ON SEMICONDUCTOR
元件分類: 穩壓器
英文描述: High Performance Resonant Mode Controller
中文描述: SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDIP16
封裝: LEAD FREE, PLASTIC, DIP-8
文件頁數: 21/27頁
文件大小: 345K
代理商: NCP1395BPG
NCP1395A/B
http://onsemi.com
21
To the contrary, when the internal BO signal is high
(A and B pulse), the IBO source is activated and creates
a hysteresis. The hysteresis level actually depends
on the circuit: NCP1395A features a 28 A whereas
the NCP1395B uses a 83
A current. Changes are
implemented to a) reduce the standby power on the
NCP1395A b) improve the noise immunity on the
NCP1395B. Knowing these values, it becomes possible to
select the turnon and turnoff levels via a few lines of
algebra:
IBO is off
V(
)
Vbulk1
Rlower
Rlower
Rupper
(eq. 1)
IBO is on
V(
)
Vbulk2
Rlower
Rlower
Rupper
IBO
Rlower
Rlower
Rupper
Rupper
(eq. 2)
We can now extract Rlower from Equation 1 and plug it
into Equation 2, then solve for Rupper:
Rupper
Rlower
Vbulk1VBO
VBO
Rlower
VBO
Vbulk1Vbulk2
IBO
(Vbulk1VBO)
If we decide to turn on our converter for Vbulk1 equals
350 V, and turn it off for Vbulk2 equals 250 V, then we
obtain:
IBO = 28 A
Rupper = 3.6 M
Rlower = 10 k
The bridge power dissipation is 400
2
/3.601 M =
45 mW when the frontend PFC stage delivers 400 V.
IBO = 83 A
Rupper = 1.2 M
Rlower = 3.4 k
The bridge power dissipation is 132 mW when the
frontend PFC stage delivers 400 V. Figure 46 simulation
result confirms our calculations.
LatchOff Protection
There are some situations where the converter shall be
fully turned off and stay latched. This can happen in
presence of an overvoltage (the feedback loop is drifting)
or when an overtemperature is detected. Due to the addition
of a comparator on the BO pin, a simple external circuit can
lift up this pin above VLATCH (5.0 V typical) and
permanently disable pulses. The V
CC
needs to be cycled
down below 5.0 V typically to reset the controller.
+
20 s
RC
To permanent
latch
+
Vlatch
IBO
Vdd
+
BO
+VBO
BO
Rlower
Rupper
Vbulk
V
CC
Q1
NTC
Vout
Figure 47. Adding a comparator on the BO pin offers a way to latchoff the controller.
In Figure 47, Q1 is blocked and does not bother the BO
measurement as long as the NTC and the optocoupler are
not activated. As soon as the secondary optocoupler senses
an OVP condition, or the NTC reacts to a high ambient
temperature, Q1 base is brought to ground and the BO pin
goes up, permanently latching off the controller.
相關PDF資料
PDF描述
NCP1395A High Performance Resonant Mode Controller(高性能諧振模式控制器)
NCP1395B High Performance Resonant Mode Controller(高性能諧振模式控制器)
NCP1400A(中文) 100 mA, Fixed Frequency PWM Step-Up Micropower Switching Regulator(100mA,固定頻率PWM升壓微功率開關穩壓器)
NCP1400ASN30T1(中文) 100 mA, Fixed Frequency PWM Step-Up Micropower Switching Regulator(微功率固定頻率脈寬調制升壓直流-直流交換器)
NCP1400ASN33T1(中文) 100 mA, Fixed Frequency PWM Step-Up Micropower Switching Regulator(微功率固定頻率脈寬調制升壓直流-直流交換器)
相關代理商/技術參數
參數描述
NCP1395D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller
NCP1395LLCGEVB 功能描述:BOARD EVAL NCP1395 RoHS:是 類別:編程器,開發系統 >> 評估板 - DC/DC 與 AC/DC(離線)SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC,步升 輸出及類型:1,非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
NCP1396A 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller featuring High−voltage Drivers
NCP1396A_10 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Performance Resonant Mode Controller featuring High-Voltage Drivers
NCP1396ADR2G 功能描述:電壓模式 PWM 控制器 RESONANT MODE CTRLR DIODE 3.3V RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel