- 您現在的位置：買賣IC網 > PDF目錄363215 > NCP1203P100 (ON SEMICONDUCTOR) PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Standby and Short Circuit PDF資料下載
參數資料
| 型號： | NCP1203P100 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Standby and Short Circuit |
| 中文描述： | 0.25 A SWITCHING CONTROLLER, 115 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封裝： | PDIP-8 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 145K |
| 代理商： | NCP1203P100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁
NCP1203
http://onsemi.com
9
Figure 15. Typical Waveforms in Short Circuit Conditions
7.8 V
12.8 V
4.9 V
V
CC
DRIVING PULSES
Calculating the V
CC
Capacitor
The V
CC
capacitor can be calculated knowing the IC
consumption as soon as V
CC
reaches 12.8 V. Suppose that a
NCP1203P60 is used and drives a MOSFET with a 30 nC
total gate charge (Qg). The total average current is thus made
of ICC1 (700 A) plus the driver current, Fsw x Qg or
1.8 mA. The total current is therefore 2.5 mA. The V
available to fully startup the circuit (e.g. never reach the
7.8 V UVLO during power on) is 12.8–7.8 = 5 V. We have
a capacitor who then needs to supply the NCP1203 with
2.5 mA during a given time until the auxiliary supply takes
over. Suppose that this time was measured at around 15 ms.
CV
CC
is calculated using the equation
C
7.5 F
. Select a 22 F/16 V and this will fit.
t · i
V
or
C
Skipping Cycle Mode
The NCP1203 automatically skips switching cycles when
the output power demand drops below a given level. This is
accomplished by monitoring the FB pin. In normal
operation, pin 2 imposes a peak current accordingly to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this setpoint reaches a
determined level (Vpin 1), the IC prevents the current from
decreasing further down and starts to blank the output
pulses: the IC enters the socalled skip cycle mode, also
named controlled burst operation. The power transfer now
depends upon the width of the pulse bunches (Figure 17).
Suppose we have the following component values:
Lp, primary inductance = 350 H
Fsw , switching frequency = 61 kHz
Ip skip = 600 mA (or 333 mV/Rsense)
The theoretical power transfer is therefore:
1
3.8 W
If this IC enters skip cycle mode with a bunch length of
10 ms over a recurrent period of 100 ms, then the total power
transfer is:
3.8 . 0.1
380 mW
.
To better understand how this skip cycle mode takes place,
a look at the operation mode versus the FB level
immediately gives the necessary insight:
Figure 16.
SKIP CYCLE OPERATION
I
P(min)
= 333 mV/R
SENSE
NORMAL CURRENT
MODE OPERATION
FB
1 V
4.2 V, FB Pin Open
3.2 V, Upper
Dynamic Range
When FB is above the skip cycle threshold (1.0 V by
default), the peak current cannot exceed 1.0 V/Rsense.
When the IC enters the skip cycle mode, the peak current
cannot go below Vpin1/3.3/Rsense. The user still has the
flexibility to alter this 1.0 V by either shunting pin 1 to
ground through a resistor or raising it through a resistor up
to the desired level. Grounding pin 1 permanently
invalidates the skip cycle operation. However, given the
extremely low standby power the controller can reach, the
PWM in noload conditions can quickly enter the minimum
t
on
and still transfer too much power. An instability can take
place. We recommend in that case to leave a little bit of skip
level to always allow 0% duty cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1203D100R2 | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Standby and Short Circuit |
| NCP1203D100R2G | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Standby and Short Circuit |
| NCP1203 | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Standby and Short Circuit |
| NCP1203D60R2 | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Standby and Short Circuit |
| NCP1203D60R2G | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Standby and Short Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1203P100G | 功能描述:電流型 PWM 控制器 100KHz Current Mode SMPS PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1203P40 | 功能描述:交流/直流開關轉換器 40KHz Current Mode RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓（最大值）:23.5 V 輸入/電源電壓（最小值）:11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel |
| NCP1203P40G | 功能描述:電流型 PWM 控制器 40KHz Current Mode SMPS PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1203P60 | 功能描述:電流型 PWM 控制器 60KHz Current Mode RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1203P60G | 功能描述:電流型 PWM 控制器 60KHz Current Mode SMPS PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。