- 您現在的位置：買賣IC網 > PDF目錄363215 > NCP1201D100R2 (ON SEMICONDUCTOR) PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power with Fault Protection Modes PDF資料下載
參數資料
| 型號： | NCP1201D100R2 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power with Fault Protection Modes |
| 中文描述： | SWITCHING CONTROLLER, 117 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 11/20頁 |
| 文件大?。?/td> | 159K |
| 代理商： | NCP1201D100R2 |
NCP1201
http://onsemi.com
11
Our power contribution example drops to 223 V x 2.1 mA
= 468.3 mW. If a resistor is installed between the mains and
the diode, you further force the dissipation to migrate from
the package to the resistor. The resistor value should be
carefully selected to account for lowline startup.
1
2
3
4
8
7
6
5
Figure 28. A Simple Diode Naturally Reduces the
Average Voltage on Pin 8
Mains
HV
Cbulk
3. Permanently force the V
CC
level above VCC
OFF
with an auxiliary winding. It will automatically
disconnect the internal startup source and the IC
will be fully selfsupplied from this winding.
Again, the total power drawn from the mains will
significantly decrease. By using this approach,
user need to make sure the auxiliary voltage never
exceeds the 16 V limit for all line conditions.
Skipping Cycle Mode
The NCP1201 automatically skips switching cycles when
the output power demand drops below a preset level. This is
accomplished by monitoring the FB pin. In normal
operation, FB pin imposes a peak current according to the
load value. If the load demand decreases, the internal loop
asks for less peak current. When this setpoint reaches the
skip mode threshold level, 1.07 V, the IC prevents the
current from decreasing further down and starts to blank the
output pulses, i.e. the controller enters the socalled Skip
Cycle Mode, also named Controlled Burst Operation. The
power transfer now depends upon the width of the pulse
bunches, Figure 29.
Suppose we have the following component values:
Lp
, primary inductance = 1.0 mH
F
sw
, switching frequency = 60 kHz
I
p
(skip) = 200 mA (or 333 mV/R
sense
)
The theoretical power transfer is therefore:
1
2
If the controller enters Skip Cycle Mode with a pulse
packet length of 20 ms over a recurrent period of 100 ms,
then the total power transfer reduced to 1.2 W x 0.2 =
240 mW.
To better understand how this Skip Cycle Mode takes
place, a look at the operation mode versus the FB pin voltage
level shown below, immediately gives the necessary insight.
Lp
Ip2
Fsw
1.2 W
(eq. 4)
1.07 V
4.2 V, FB Pin Open
2.97 V, Upper Dynamic Range
FB
Normal Current Mode Operation
Skip Cycle Operation
I
p(min)
= 333 mV / R
sense
Figure 29. Feedback Pin Voltage and Modes of Operation
When FB pin voltage level is above the skip cycle threshold
(1.07 V by default), the peak current cannot exceed
0.9 V/R
sense
. When the IC enters the skip cycle mode, the
peak current cannot go below V
SKIP
/3.3. By using the peak
current limit reduction scheme, the skip cycle takes place at
a lower peak current, which guarantees noise free operation.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1201D60R2 | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power with Fault Protection Modes |
| NCP1201D60R2G | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power with Fault Protection Modes |
| NCP1201P100 | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power with Fault Protection Modes |
| NCP1201P100G | PWM Current-Mode Controller for Universal Off-Line Supplies Featuring Low Standby Power with Fault Protection Modes |
| NCP1201 | PWM Current Mode Controller for Universal Off Line Supplies Featuring Low Standby Power with Fault Protection Modes(PWM電流模式控制器，適用于通用離線電源，以低待機功耗與故障保護模式為特點) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1201D100R2G | 功能描述:電流型 PWM 控制器 ANALOG POWER CONV RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1201D60R2 | 功能描述:電流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1201D60R2G | 功能描述:電流型 PWM 控制器 Current Mode PWM w/Fault Protection RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1201P100 | 功能描述:電流型 PWM 控制器 Current Mode PWM RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1201P100G | 功能描述:電流型 PWM 控制器 Current Mode PWM w/Fault Protection RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。