- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCP1081DEG (ON Semiconductor)IC CONV CTLR POE-PD 40W 20-TSSOP Datasheet資料下載
參數資料
| 型號： | NCP1081DEG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 13/18頁 |
| 文件大?。?/td> | 257K |
| 描述： | IC CONV CTLR POE-PD 40W 20-TSSOP |
| 標準包裝： | 74 |
| 類型： | 以太網供電開關（PoE） |
| 應用： | 遠程外設（工業控制，相機，數據訪問） |
| 內部開關： | 是 |
| 電流限制： | 1.1A |
| 電源電壓： | 0 V ~ 57 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 20-TSSOP-EP |
| 包裝： | 管件 |
NCP1081
http://onsemi.com
13
As soon as the application is powered by the DC-DC
converter and completes initialization, the microprocessor
should check if the NCP1081 detected a two event hardware
classification by reading its digital input (pin IN1 in this
example). If pin IN1 is low, the application knows power is
supplied by a IEEE802.3at compliant PSE, and can deliver
power up to the level specified by the IEEE802.3at standard.
Otherwise the application will have to perform a Layer 2
classification with the PSE. There are several scenarios for
which the NCP1081 will not enable its nCLASS_AT pin:
" The PSE skipped the classification phase.
" The PSE performed a one event hardware classification
(it can be a IEEE802.3af or a 802.3at compliant PSE
with Layer 2 engine).
" The PSE performed a two event hardware classification
but it did not properly control the input voltage in the
mark voltage window, (for example it crossed the reset
range).
Power Mode
When the classification handshake is completed, the
PSE and PD devices move into the operating mode.
Under Voltage Lock Out (UVLO)
The NCP1081 incorporates an under voltage lock out
(UVLO) circuit which monitors the input voltage and
determines when to apply power to the DCDC controller.
To use the default settings for UVLO (see Table 3), the pin
UVLO must be connected to VPORTN
1,2
. In this case the
signature resistor has to be placed directly between
VPORTP and VPORTN
1,2
, as shown in Figure 9.
Figure 9. Default UVLO Settings
UVLO
VPORTP
VPORTN1,2
NCP1081
VPORT
Rdet
To define the UVLO threshold externally, the UVLO pin
must be connected to the center of an external resistor
divider between VPORTP and VPORTN
1,2
as shown in
Figure 10. The series resistance value of the external
resistors must add to 25.5 kW and replaces the internal
signature resistor.
Figure 10. External UVLO Configuration
UVLO
VPORTN1,2
NCP1081
VPORT
R2
R1
VPORTP
For a Vuvlo_on desired turnon voltage threshold, R1 and
R2 can be calculated using the following equations:
R1 ) R2 + R
det
R2 +
1.2
V
ulvo_on
R
det
When using the external resistor divider, the NCP1081 has
an external reference voltage hysteresis of 15 percent typical.
Inrush and Operational Current Limitations
The inrush current limit and the operational current limit
are programmed individually by an external Rinrush and
Rilim1 resistors respectively connected between INRUSH
and VPORTN
1,2
, and between ILIM1 and VPORTN
1,2
as
shown in Figure 11.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1082DEG | IC CONV CTLR POE-PD 13W 20-TSSOP |
| NCP1083DEG | IC CONV CTLR POE-PD 40W 20-TSSOP |
| NCP1501DMR2G | IC REG SGL BUCK/LINEAR 8MICRO |
| NCP1578MNR2G | IC REG DL BCK/LINEAR SYNC 20-QFN |
| NCP1601BDR2G | IC PFC CTRL CRM/TRANSITION 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1081DER2G | 功能描述:DC/DC 開關控制器 POE-PD 40W DC-DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| NCP1081SPCGEVB | 功能描述:電源管理IC開發工具 HPOWER POE-PD SPLITTER RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1082 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Integrated PoE-PD & DC-DC Converter Controller with 9V Auxiliary Supply Support |
| NCP1082DEG | 功能描述:直流/直流開關轉換器 POE-PD 13W DC-DC AUX SUPP RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| NCP1082DER2G | 功能描述:直流/直流開關轉換器 POE-PD 13W DC-DC AUX SUPP RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。