- 您現在的位置：買賣IC網 > PDF目錄361089 > NCP1012ST65T3 (ON SEMICONDUCTOR) Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS PDF資料下載
參數資料
| 型號： | NCP1012ST65T3 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 穩壓器 |
| 英文描述： | Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
| 中文描述： | 1 A SWITCHING REGULATOR, 71 kHz SWITCHING FREQ-MAX, PSSO4 |
| 封裝： | PLASTIC, SOT-223, 4 PIN |
| 文件頁數： | 9/24頁 |
| 文件大小： | 324K |
| 代理商： | NCP1012ST65T3 |
NCP1010, NCP1011, NCP1012, NCP1013, NCP1014
http://onsemi.com
9
APPLICATION INFORMATION
Introduction
The NCP101X offers a complete currentmode control
solution (actually an enhanced NCP1200 controller section)
together with a highvoltage power MOSFET in a
monolithic structure. The component integrates everything
needed to build a rugged and lowcost SwitchMode Power
Supply (SMPS) featuring low standby power. The Quick
Selection Table on Page 2, details the differences between
references, mainly peak current setpoints and operating
frequency.
No need for an auxiliary winding:
ON Semiconductor
Very High Voltage Integrated Circuit technology lets you
supply the IC directly from the highvoltage DC rail. We call
it Dynamic SelfSupply (DSS). This solution simplifies the
transformer design and ensures a better control of the SMPS
in difficult output conditions, e.g. constant current
operations. However, for improved standby performance,
an auxiliary winding can be connected to the V
CC
pin to
disable the DSS operation.
Shortcircuit protection:
By permanently monitoring the
feedback line activity, the IC is able to detect the presence of
a shortcircuit, immediately reducing the output power for
a total system protection. Once the short has disappeared, the
controller resumes and goes back to normal operation.
Failsafe optocoupler and OVP:
When an auxiliary
winding is connected to the V
CC
pin, the device stops its
internal Dynamic SelfSupply and takes its operating power
from the auxiliary winding. A 8.7 V active clamp is
connected between V
CC
and ground. In case the current
injected in this clamp exceeds a level of 7.4 mA (typical),
the controller immediately latches off and stays in this
position until V
CC
cycles down to 3.0 V (e.g. unplugging the
converter from the wall). By adjusting a limiting resistor in
series with the V
CC
terminal, it becomes possible to
implement an overvoltage protection function, latching off
the circuit in case of broken optocoupler or feedback loop
problems.
Low standbypower:
If SMPS naturally exhibits a good
efficiency at nominal load, it begins to be less efficient when
the output power demand diminishes. By skipping unneeded
switching cycles, the NCP101X drastically reduces the
power wasted during light load conditions. An auxiliary
winding can further help decreasing the standby power to
extremely low levels by invalidating the DSS operation.
Typical measurements show results below 80 mW @
230 Vac for a typical 7.0 W universal power supply.
No acoustic noise while operating:
Instead of skipping
cycles at high peak currents, the NCP101X waits until the
peak current demand falls below a fixed 1/4 of the maximum
limit. As a result, cycle skipping can take place without
having a singing transformer
…
You can thus select cheap
magnetic components free of noise problems.
SPICE model:
A dedicated model to run transient
cyclebycycle simulations is available but also an
averaged version to help close the loop. Readytouse
templates can be downloaded in OrCAD’s PSpice, and
INTUSOFT’s IsSpice4 from ON Semiconductor web site,
NCP101X related section.
Dynamic SelfSupply
When the power supply is first powered from the mains
outlet, the internal current source (typically 8.0 mA) is
biased and charges up the V
CC
capacitor from the drain pin.
Once the voltage on this V
CC
capacitor reaches the VCC
OFF
level (typically 8.5 V), the current source turns off and
pulses are delivered by the output stage: the circuit is awake
and activates the power MOSFET. Figure 13 details the
internal circuitry.
Figure 13. The Current Source Regulates V
CC
by Introducing a Ripple
Vref OFF = 8.5 V
Vref ON = 7.5 V
Vref Latch = 4.7 V*
+
Internal Supply
+
Vref
VCC
OFF
+200 mV
(8.7 V Typ.)
V
CC
+CV
CC
Startup Source
Drain
*In fault condition
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1013ST65T3 | Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
| NCP1014ST100T3 | Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
| NCP1014ST65T3 | Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
| NCP1012ST130T3 | Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
| NCP1013 | Self-Supplied Monolithic Switcher for Low Standby- Power Offline SMPS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1012ST65T3G | 功能描述:電流型 PWM 控制器 Low Standby Power Monolithic Switcher RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1013 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Power Factor Controllers |
| NCP1013/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Self-Supplied Monolithic Switcher for Low Standby-Power Offline SMPS |
| NCP1013ADAPGEVB | 功能描述:電源管理IC開發工具 NCP1013 6/12W ADAPTER EVB RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1013AP065 | 功能描述:電流型 PWM 控制器 Low Standby Power RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。