- 您現在的位置：買賣IC網 > PDF目錄376214 > MXD7210ML (Electronic Theatre Controls, Inc.) Silver Mica Capacitor; Capacitance:5000pF; Capacitance Tolerance:+/- 5%; Series:CD30; Voltage Rating:500VDC; Capacitor Dielectric Material:Mica; Termination:Radial Leaded; Lead Pitch:11.1mm; Leaded Process Compatible:Yes RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | MXD7210ML |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Silver Mica Capacitor; Capacitance:5000pF; Capacitance Tolerance:+/- 5%; Series:CD30; Voltage Rating:500VDC; Capacitor Dielectric Material:Mica; Termination:Radial Leaded; Lead Pitch:11.1mm; Leaded Process Compatible:Yes RoHS Compliant: Yes |
| 中文描述： | 低成本，低噪聲-10克雙軸加速度計的數字輸出 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 647K |
| 代理商： | MXD7210ML |
MXD7210GL/HL/ML/NL PIN DESCRIPTIONS
V
DD
– This is the supply input for the circuits and the
sensor heater in the
accelerometer
. The DC voltage should
be between 2.7 and 5.25 volts. Refer to the section on PCB
layout and fabrication suggestions for guidance on external
parts and connections recommended.
COM
– This is the ground pin for the
accelerometer
.
TP
– This pin should be connected to ground.
Xout
– This pin is the digital output of the X-axis
acceleration sensor. It is factory programmable to 100Hz or
400Hz. The user should ensure the load impedance is
sufficiently high as to not source/sink >250
μ
A typical.
While the sensitivity of this axis has been programmed at
the factory to be the same as the sensitivity for the y-axis,
the
accelerometer
can be programmed for non-equal
sensitivities on the x- and y-axes. Contact the factory for
additional information.
MEMSIC MXD7210GL/HL/ML/NL
Page 4 of
10
2003.08.04
Yout
–
This pin is the digital output of the Y-axis
acceleration sensor. It is factory programmable to 100Hz or
400Hz. The user should ensure the load impedance is
sufficiently high as to not source/sink >250
μ
A typical.
While the sensitivity of this axis has been programmed at
the factory to be the same as the sensitivity for the x-axis,
the
accelerometer
can be programmed for non-equal
sensitivities on the x- and y-axes. Contact the factory for
additional information.
DISCUSSION OF TILT APPLICATIONS AND
RESOLUTION
Tilt Applications:
One of the most popular applications of
the MEMSIC accelerometer product line is in
tilt/inclination measurement. An accelerometer uses the
force of gravity as an input to determine the inclination
angle of an object.
A MEMSIC accelerometer is most sensitive to changes in
position, or tilt, when the accelerometer’s sensitive axis is
perpendicular to the force of gravity, or parallel to the
Earth’s surface. Similarly, when the accelerometer’s axis is
parallel to the force of gravity (perpendicular to the Earth’s
surface), it is least sensitive to changes in tilt.
Table 1 and Figure 2 help illustrate the output changes in
the X- and Y-axes as the unit is tilted from +90
°
to 0
°
.
Notice that when one axis has a small change in output per
degree of tilt (in m
g
), the second axis has a large change in
output per degree of tilt. The complementary nature of
these two signals permits low cost accurate tilt sensing to
be achieved with the MEMSIC device (reference
application note AN-00MX-007).
M
Figure 2: Accelerometer Position Relative to Gravity
X-Axis
X-Axis
Orientation
To Earth’s
Surface
(deg.)
90
-1.000
85
-0.996
80
-0.985
70
-0.940
60
-0.866
45
-0.707
30
-0.500
20
-0.342
10
-0.174
5
-0.087
0
0.000
Table 1: Changes in Tilt for X- and Y-Axes
Resolution
: The accelerometer resolution is limited by
noise. The output noise will vary with the measurement
bandwidth. With the reduction of the bandwidth, by
applying an external low pass filter, the output noise drops.
Reduction of bandwidth will improve the signal to noise
ratio and the resolution. The output noise scales directly
with the square root of the measurement bandwidth. The
maximum amplitude of the noise, its peak- to- peak value,
approximately defines the worst case resolution of the
measurement. With a simple RC low pass filter, the rms
noise is calculated as follows:
Noise (mg rms) = Noise(mg/
Hz
) *
The peak-to-peak noise is approximately equal to 6.6 times
the rms value (for an average uncertainty of 0.1%).
Y-Axis
X Output
(
g
)
Change
per deg.
of tilt
(m
g
)
0.15
1.37
2.88
5.86
8.59
12.23
15.04
16.35
17.16
17.37
17.45
Y Output
(
g
)
Change
per deg.
of tilt
(m
g
)
17.45
17.37
17.16
16.35
15.04
12.23
8.59
5.86
2.88
1.37
0.15
0.000
0.087
0.174
0.342
0.500
0.707
0.866
0.940
0.985
0.996
1.000
)
*
)
(
(
Hz
Bandwidth
相關PDF資料 |
PDF描述 |
|---|---|
| MXD7210NL | Low Cost, Low Noise +-10 g Dual Axis Accelerometer with Digital Outputs |
| MXO45 | Metal DIP Clock Oscillator |
| MXO45-2C | Metal DIP Clock Oscillator |
| MXO45-2I | Metal DIP Clock Oscillator |
| MXO45-3C | Metal DIP Clock Oscillator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MXD7210NL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low Cost, Low Noise +-10 g Dual Axis Accelerometer with Digital Outputs |
| MX-DAH4 | 功能描述:焊接工作站設備 ESD Air Hose U.S. standard fitting RoHS:否 制造商:OK International 產品:Stands 類型:Soldering and Rework System 最大溫度:+ 55 C 電纜類型:US Cord Included |
| MX-DAR1 | 功能描述:焊接工作站設備 Air Regulator/Filter w/ fittings RoHS:否 制造商:OK International 產品:Stands 類型:Soldering and Rework System 最大溫度:+ 55 C 電纜類型:US Cord Included |
| MX-DCF1 | 功能描述:去焊 DS1 Filter Pack:15 Chamber liners 6 RoHS:否 制造商:Chip Quik 產品:Desoldering Tools 類型: |
| MX-DCF1F | 功能描述:去焊 DS1 Fume Filters MX ACCESS RoHS:否 制造商:Chip Quik 產品:Desoldering Tools 類型: |
發布緊急采購，3分鐘左右您將得到回復。